Dear researchers,
Does anyone knows approximate passive film composition of the film formed by interaction of iron or steel with chromate inhibitors?
https://www.sciencedirect.com/topics/materials-science/passive-film
Dear colleges, Does anyone know solubility of Fe(NO3)3x9H2O in acetone g/100 ml Thanks in advance Branimir
26 May 2024 2,383 2 View
Power, memory, symbols, legitimation
06 February 2024 552 1 View
Dear colleges, After activation of pristine carbon felt by chemical oxidation, electrochemical activity increased 20 times, but contact angle remaining practically the same. By XPS increases of...
20 January 2024 7,443 4 View
Does anyone knows what is the minimum thickness of metallic coating to avoid supstrata signal in XRD or EDS measurements.. For example, MoFe alloy on Fe supstrate. Thanks in advance
21 November 2023 6,038 6 View
Dear colleagues, Does anyone knows specific energy consumption for production of metallic lithium, sodium, magnesium and calcium by molten salt electrolysis. Reliable reference will be nice. Many...
07 August 2023 9,276 1 View
Dear colleagues, Does anyone know producers of smaller O2 and CO2 sensors, PC, USB conections with softver, for measuring concentations during electrolysis? Any related paper will be...
02 July 2022 5,155 0 View
Dear Rg colleges, Does sombady eny time obseved decreasec charge discharge efficiency of electrode materials with decrease current? Very unusual phenomenon, but we got such behavior on the two...
17 March 2022 5,181 0 View
Does any experienced such strange I overloads with Gamry 1010E (potentiostat is grounded), with cyclic polarization using Corrosion softver. Please see attached figure. Is there any solution to...
09 September 2019 7,708 10 View
Dear RG colleges, Does anyone know the magnitude of conductivity of solid lead sulfate (even is nonconducting)
02 July 2019 3,697 8 View
Does anyone know a reliable PPy HOMO and LUMO positions vs. absolute vacuum scale? I have some data 5 eV for HOMO, 2.45 eV (dedoped) and 3.3 eV (doped) for LUMO. Is it correct, and are they pH...
01 July 2014 4,666 1 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...
06 August 2024 3,176 0 View
Generally, the target material is Mo, Co, Cu, Fe, Cr, etc, so on what basis should we choose this material?
31 July 2024 5,824 0 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
I am currently working on a project that involves extracting cell membranes, for which we disrupt the cells using sonication. During the initial extraction process, we add protease inhibitors to...
30 July 2024 7,077 1 View
Dear all: I am modifying Bismuth Tungstate with Hematite (Fe2O3), so I would like to know about how much Iron(+3) can form a solid solution in a Bismuth Oxide matrix. Best wishes Marco
29 July 2024 2,163 1 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View