What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

Why tick's salivary gland extract didn't run in the gel (SDS PAGE )??

Greetings, I want to make SDS PAGE for my sample (Tick salivery gland extract), I tried concentrations 10%, 12%. I also tried high molecular weight ladder. But the protein stopped at the top and...

25 February 2021 7,698 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

How to measure the pH of Peat Soil?

Peat possess organic content above 75% and is highly acidic in nature (i.e. pH < 4). Before commencing stabilization, it is mandatory to know about the pH level of peat. Therefore, your...

18 February 2021 9,424 7 View

How to Measure Consumer Willingness To Change from petroleum-fueled vehicle to electric vehicle?

I wanted to calculate the probability of one consumer shifting from using a petroleum-fueled vehicle to an electric vehicle. Since my background is in engineering I do not know much about how to...

15 February 2021 9,190 5 View

Can Immunogenic BNT162b vaccines protect HUMANS from SARS-CoV-2?

"A safe and effective vaccine against COVID-19 is urgently needed in quantities sufficient to immunise large populations. We report the preclinical development of two BNT162b vaccine candidates,...

11 February 2021 6,628 9 View

Having trouble mounting the sections on the slides for IHC staining, what solution should I use?

Hello everyone, I just started learning IHC staining and I have some frozen sections to practice with in a 96-well plate. I'm having trouble mounting the sections on the slide, a colleague told me...

08 February 2021 6,880 3 View

Does Abaqus plugin AM-Modeler predict the same temperature/crystallinity history as UMATHT user-subroutine?

During AM process, progressively activation of elements can predict the temperature/crystallinity history, including surroundings heat losses and than this data could be used to determine the...

06 February 2021 4,686 1 View

How to use Image Lab to take an image for the bands and the ladder in the same image merged together in Western Blot?

Hello everyone. I was trying to use Image Lab software to take an image of both the ladder and the samples merged together in one image to see the position of the bands according to the ladder MW,...

04 February 2021 9,996 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

The most suitable method to calculate the stress intensity factor in the presence of contact between the crack lips?

I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...

21 February 2021 8,694 4 View

Amorphous silica XRD peak at around 10 degree?

21 February 2021 3,417 5 View

How to calculate time needed to evacuate a pressure from a tank using a pump?

Dear I have an air reservoir with 50 bar pressure , this reservoir is fed by 2 bar air pressure source, I would like to instal air pump ( 30 m3/h ) to evacuate the 2 bar fed pressure so I always...

06 February 2021 3,520 3 View

Which software is the best to model a non-linear concrete (ABAQUS, ANSYS,ADINA, ATENA, etc.)?

What is the best finite element modeling software packages for modeling non-linear and fracture analysis of CONCRETE? I've had some with ABAQUS standart/explicit, but I would like to learn if...

27 January 2021 330 6 View

Do we need to keep looking for the fracture angle after the Puck's failure initiation is reached?

Greetings to everyone, Our team is currently working on the development of a VUMAT code in Abaqus for composite modelling using the Puck's failure theory as damage initiation criteria. Currently...

20 January 2021 6,367 1 View

How to prove the formation of a synthesis product using NMR ?

Hello, I am trying to identify the formation of a synthesis product. Knowing the precursors, I focused on the identification of the H-C long-range coupling between sites (a/b) and (a/c) using...

19 January 2021 8,438 5 View

Fracture energy of concrete at sub-zero temperatures?

Both tensile and compressive strengths of concrete increase with the decrease in temperature. With this in mind and considering that fracture energy is in direct correlation with the so-called...

18 January 2021 8,778 4 View

Permeability of fractured reservoirs?

Hi all, What I know the permeability of matrix and fracture can be in a broad range in fractured reservoirs. Am looking for the most usual range for their permeability separately. I will be highly...

15 January 2021 5,271 2 View

Why the fracture energy of concrete increases with the rise in temperature?

Given the degradation of mechanical properties in concrete under elevated temperature namely, tensile strength, modulus of elasticity, compressive strength, etc., what is the justification behind...

15 January 2021 3,651 4 View