Optimal Does of Nanoparticles for Injection?

More Vincent Fan's questions See All

Optimal Conditions for DBCO-azide Reaction?

I was trying to conjugate dye and PEG onto DBCO functionalized nanoparticles. The dye I use is azide-Cy5 and the PEG is azido-PEG24-NHS. I first react the dye with particles for 1 whole day...

09 October 2019 5,121 3 View

Does anyone have the protocol for lymph node sectioning and imaging?

I'm running a study in which I will inject some nanoparticles into mice and then section the lymph node and visualize it with confocal. Does anyone have the protocal for the lymph node sectioning...

08 September 2019 4,819 3 View

Incubation Time for Primary Antibody Staining?

Hello, I wanna stain some RAW 264.7 macrophages with anti-mice MHC-II and CD80 antibodies to run flow cytometry. Last time I tried 4C for 1hr but it barely worked. This time I'm thinking maybe I...

11 December 2018 6,234 13 View

Anyone plz suggest relevant topic for research in image processing+Deep learning.?

I have selected brain tumor images ...but now found that already lots of research done n this topic.

03 March 2021 5,774 3 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

Can chitosan alone can act as a reducing agent for Cu(0) nanoparticle sythesis?

[Synthesizing Cu nanoparticles without using chemical reductants]

01 March 2021 8,359 1 View

How to find the mode of classified ocean colour images?

Hello, I have classified 10 S3 OLCI images from the same area (althouth not the same size and/or quadrant) and I would like to do a final image using the mode of the pixel of these 10 images. I...

01 March 2021 9,874 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

Hakkı Nur

The amount of toxic substance in the content of the synthesized nanoparticle is important. Because it can prevent blood clotting. The toxic picture can take shape quickly. Therefore, you must report the content of the synthesized substance.

Isam Eldin Hussein Elgailani

Please look at the following below links which may help you in your analysis:

https://www.ncbi.nlm.nih.gov/pmc/articles/PMC5795468/pdf/etm-15-03-2994.pdf

https://www.nature.com/articles/srep25613.pdf

https://journals.sagepub.com/doi/pdf/10.1177/0192623307310946

Thanks

Aviral Kumar

The dosage and concentration can depend on a lot of factors like the route of injection (i.p, i.m, oral, etc), the buffer in which you want to dissolve.