Open-stator-winding DFIG?

10 October 2018 0 2K Report

Respected Research Fellows

I hope everyone will be fine

I need your help regarding the modeling of Open winding DFIG in MATLAB/SIMULINK, if anyone kindly provide me with some guidelines or suggestions.

Badges
Science topic

Similar topics
Engineering
Modeling

More Zakiud Din's questions See All

Poles or eigenvalues of Transfer Matrix?

Hope all will be good I have transfer matrix of the form G=(1/s^2+3s+5)*[s s-1 s+2] row1 [0 0 0]row2 How i will find the Poles or eigenvalues of this?

10 November 2017 4,114 0 View

How to know about the S-function of DFIG?

In Simulink library we have asynchronous generator ,i want to know about the S-Function of the this generator. How can i find it

07 August 2017 6,997 5 View

How to change the direction of output of voltage Source Inverter (VSI)

I have designed VSI in SIMULINK for grid connected operation of DFIG ,but the Output voltage of VSI is similar to stator voltage,and i want the flow from VSI toward the DFIG ,not from DFIG stator...

07 August 2017 6,872 2 View

Can i find some basic ideas about asynchronous generator ?

Hi all I want to know about the basic equation of stator and rotor voltage and power equation of 3 phase asynchronous generator connected to grid. I also want to know about the load angle of the...

06 July 2017 8,708 4 View

What should be the rating of voltage source converter (VSC) in grid connected operations?

Hi all I am designing a voltage source converter (VSC) for variable speed constant frequency operation i.e Grid connected DFIG,what should be the rating of the converter ,like which parameters...

05 June 2017 349 2 View

How to operate grid connected VSI in close loop?

I have modeled grid connected inverter by using grid voltage oriented control ,everything is fine but the current is too high,where can be the fault in circuit. Can anyone guide me

04 May 2017 1,460 3 View

I want to model open winding DFIG in MATLAB/SIMULINK,The neutral point of the stator winding is open?

The Neutral point of stator winding is open.I need a SIMULINK Model of this type of DFIG.

03 April 2017 9,448 0 View

Is there any circuit for calculation of external resistance of cow bar circuit for grid connected double fed induction generator?

I need circuit diagam

11 December 2016 2,443 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View