The rest of my variables are multiple items.
Check the following post:
https://www.researchgate.net/post/Did_you_use_single-item_measures_in_your_SEM_models_How_did_it_work_out
and this article:
http://www.palgrave-journals.com/jma/journal/v1/n2/full/jma20137a.html
Regards
Asish
i would recommend conceptualize all your variables as a second order contract
For this, you have to fix loading and error term (for example 1 and 0.0). Without this, model will not be estimated.
Regard
Imtiaz
The single item will become as observed variable. You can run as usual with other latent variables
Hi Thien,
Basically you need to adjust for measurement error through attenuation. The below link explains how this is done in AMOS.
Wanous & Reichers (1996) is the one to look at for dealing with single items and measurement error.
Best of luck with your research.
http://spssx-discussion.1045642.n5.nabble.com/Correcting-measurement-error-in-AMOS-td5726574.html
Appreciate for all the responses. I did as recommended By Wan Mohamad and it ran. Cheers
Hi Chalamalla, that variable was actual literacy score. The rest were Likert-scale items for latent variables. This issue was solved. Cheers
Currently working on project related to behavioural finance
07 August 2016 3,259 0 View
Hayes (2013) suggested to use his PROCESS macro. Not sure if AMOS output is appropriate and sufficient to run the macro.
05 June 2016 2,345 4 View
Is considering to impute data to create composite variable using regression imputation in AMOS. With that, structural model would be free from observed items.
05 June 2016 8,252 3 View
Both mediators are in same level.
05 June 2016 6,708 8 View
There's argument efa and cfa can't be performed using same dataset. Does this consider as violation to this rule? . As measurement model us also known as cfa.
05 June 2016 689 9 View
My CFA has nine variables, of which one is a single measure variables. Thanks
04 May 2016 9,033 8 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Are there any statistical methods to justify your sampling technique using SPSS or AMOS?
05 August 2024 9,153 4 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View