Need information about FeNi alike alloy recrystalization textures.?

03 August 2022 0 9K Report

Curently developing FeNiCoAlTiB superelastic alloy, texture is a big parameter to take account, and to be correctly refined. Any information is greatly appreciated.

Badges
Science topic

More Juan Cassinerio's questions See All

How to reduce the material coming out of the torque rheometer?

A physical mix was in vitro evaluated on a torque rheometer. The composition was predominantly recycled polypropylene (PP), yet the melt flow index (MFI) was found to be excessively high....

25 June 2024 10,154 0 View

Who is the use of Generative Artificial Intelligence in Qualitative Research?

One of the most intriguing frontiers in contemporary research is the application of Generative Artificial Intelligence (GenAI) in qualitative research. This technological advance offers tools that...

13 June 2024 781 2 View

¿Que enfoque metodológico me recomiendan para abordar los gremios tróficos en un área natural de BST?

Me interesa investigar la distribución espacial de los gremios tróficos de aves en un área natural específica de bosque seco tropical, analizando la abundancia relativa de cada gremio en las...

12 June 2024 9,313 1 View

Laser for perovskite module?

Hi, I'd like to know if someone knows about a company where I can buy an affordable laser-scriber for perovskite films and another thin film for the fabrication of modules. Many thanks,

31 May 2024 2,841 0 View

Fluorescence spectroscopy: signal from water?

In order to proceed with the quantification of an Azide Alkyne Cycloaddition reaction efficiency by using a fluorogenic probe with Cy5-DBCO, I first need to construct a calibration curve. The...

16 May 2024 6,266 5 View

Can I calculate the high and low spin of the material in Quantum espresso?

I would like to simulate the high and slow spin configuration of a metal oxide. I am using QE for it, but in my research, I found that this kind of calculus is not possible. Or if it is possible,...

15 May 2024 6,497 3 View

Does anyone have a protocol for MPs assessment in fresh snow?

Dear colleagues Could someone send to me an already validated protocol for microplastic analysis in fresh snow that includes sampling and analysis in the lab? I suppose there is no need to digest...

15 May 2024 2,378 1 View

How can technology help hospitalized children?

How do you think technology can help hospitalized children?

10 May 2024 6,508 2 View

What mode can confocal microscopy use to observe metal surfaces?

How can confocal microscopy observe cells stained on metal surfaces

28 April 2024 2,804 1 View

How can confocal microscopy observe cells stained on metal surfaces?

How to observe cells stained on metal surfaces using confocal microscopy,How to adjust the confocal mode

28 April 2024 3,103 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

Is the black sediment consider as sand? If not, how can I filter it out?

Hi researchers! I'm working on soil texture analysis, and the end result for sand is doubtful because there is black sediment appearing after drying, as shown in the figure. Is it considered sand?...

30 July 2024 557 2 View

Why practical assessments of dislocation density by XRD ignores the texture which apparently affects the result?

As one can read in numerous papers on this matter, the dislocation density is derived from the dependence of peak broadening on the diffraction angle, that is, on considered reflections. Thus, to...

28 July 2024 6,496 5 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

How can I calculate spin texture using Quantum Espresso for non-colinear case ?

I want to calculate the spin texture for the electronic band structure obtained from SOC calculation. Is there any way for calculation of spin texture using quantum espresso??

19 July 2024 8,571 1 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View