Hello Everyone!!
im looking fro meshing tool which can be used for the complex geometry. and same geometry can be imported to MATLAB also.
after importing to MatLab i would like to solve the differential equation using FVM.
Hi!
Go through the thread...
https://in.mathworks.com/matlabcentral/fileexchange/53993-quickersim-cfd-toolbox
https://in.mathworks.com/matlabcentral/answers/232140-computational-fluid-dynamics-cfd-and-matlab
https://www.cfd-online.com/Forums/blogs/far/1555-best-mesh-generation-software.html
https://www.featool.com
http://www.pointwise.com
https://www.cfd-online.com/Forums/ansys-meshing/90237-exporting-mesh-read-matlab.html
Hello
You can find some meshing tools in Matlab Webpage
https://www.mathworks.com/matlabcentral/fileexchange/
Also, if you know how to make program, you can edit some of them.
Thank you @mahesh sir for your valuable answer
Thank you @Sosimo sir
Hello Everyone!! i'm working on Hydraulics particularly on Scouring, i have Scour depth data and Parameters affecting to scour. now i would like to carryout sensitivity analysis on the parameters...
03 April 2019 9,250 14 View
hello everyone!! we often encounter with the partial differential terms. (partial)dy/dx. i have shown the exact form of the equation in which i am interested in. if i have the values of both...
03 April 2019 3,833 3 View
Hello Everyone!! im looking for the what should be the threshold value for performance criteria such as coefficient of correlation, Nash coeff. p value, error, etc.. i understand i cannot put all...
03 April 2019 3,663 5 View
Hello everyone!! for the particular station by applying trend analysis techniques (Sen's, Mankendall or innovative) one can find the Trend. But i would like to know, what is the Rainfall and...
08 September 2018 6,650 0 View
Hello Everyone!! i'm trying to estimate epsilon( turbulent dissipation rate) by ADV data. i need to estimate all nine elements of fluctuating velocity gradient tensor, question is how to quantify...
08 September 2018 4,525 5 View
hello everyone!!! we are doing rainfall runoff mdelling Using SWAT. we have two gauging sites where levels are measured. one locations is weir and another one is controll crossestion. both the...
05 June 2018 7,223 4 View
Hello everyone!! im just wondering, is it possible to find the hourly Tidal levels? if we have understood the different factors contributing the Tidal levels, i guess it is possible to determine...
05 June 2018 7,079 6 View
Hello everyone!! I would like to know , How to convert hourly stream flow discharge to daily discharge ? Please help
04 May 2018 916 21 View
Hello everyone!! i'm predicting the future rainfall using SDSM Software. while calibrating (Period 1970 to 2000) the model for, conditional monthly frequency, SDSM is giving an error says "...
04 May 2018 1,058 5 View
Hello everyone!! i have velocity profile data in vertical plane for 5 10 15 20 cm distance away from the wall. now i would like to plot it in single figure showing the variation of velocity...
04 May 2018 4,518 7 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...
11 August 2024 9,801 2 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View