Fluorescent tyramide protocol ?

Hello, Im asking to check if anyone has a protocol for preparing fluorescent tyramide for fluorescent in situ hybridization. The one Im using isnt working, so if anyone has one that works, can you...

05 November 2020 9,566 3 View

What is the talents' best identification tool?

There are different identification tools to identify talented individuals, which tool you think is the most successful one to properly identify them?

04 October 2019 5,734 3 View

Problem in Wi Fi connection ?

I have a problem with the modem (D-link). When you set up the modem, I connect normally, but after a few time, the Wi-Fi network is disconnected and when I try to re-enter in the network, it does...

03 September 2019 8,187 4 View

What's the simplest method to determine the HOMO and LUMO energy levels of insoluble organic semiconductors?

HOMO and LUMO energy levels determination is un important step to confirme organic materials application in OSCs

19 February 2019 1,327 5 View

According to SJR, there are a Cataloging and Classification Quarterly (Q1, Q2, Q3 and Q4). I would like to know the Q1 and Q2 of psychology journals?

Dear Colleagues, According to SJR, there are a Cataloging and Classification Quarterly (Q1, Q2, Q3 and Q4). I would like to know the Q1 and Q2 of psychology journals? Thanks a lot

08 September 2018 8,737 1 View

No title

24 May 2017 3,415 18 View

No title

17 October 2016 5,906 2 View

I have a program written in MATLAB?

Write a program that receives A,B,C matrixes and systems are A.B.C controlable and obser n * n matrix A and grade B and C, respectively, and l m and 2m> n is. Parallel to obtain compensation k...

08 February 2016 4,054 1 View

What could be these bands?

after running RT-PCR, i get the right size of amplified gene fragment, which is a reference gene, but i get also another light bands much smaller than mein, any explanation please?? amplicon size:...

24 September 2015 5,084 9 View

What is the procedure for calculating the size of the particle to the powder?

what is the relationship between the optical and magnetic properties?

19 January 2015 7,759 2 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View