Linear Eddy Mixing (LEM) model

01 January 1970 0 5K Report

Can anyone please recommend me an online course in an introduction to turbulent combustion, specifically 1d models like Linear Eddy Mixing (LEM) model ? Thanks in Advance

Badges
Science topic

More Abdelrazik Essam's questions See All

Literature Review for The Impact of Digital Transformation on Project Management ?

i need 6 previous studies containing The aim of this study, the type of the study,Results Recommendations, publisher, year of creation

17 March 2024 3,495 3 View

How to get HOMO and LUMO coefficients at the reactive sites for the reactants from gaussian?

I want to calculate the HOMO-LUMO coefficient for each atom of my molecules. I am using Gaussian software for calculations. As I can see in multiwfn manual, I can get the orbital percentage but...

08 July 2023 10,011 1 View

Which is better in diagnosing compounds, HPLC method or FPLC method and why?

I want using two methods to spread compounds from crud solution.

05 January 2023 3,729 4 View

Does anyone have suggestions as to which? would be the best modelling software in Ro + DI?

I'm planning to build a model of a hybrid reverse osmosis and deionisation , for my research probably using wav. I don't have a lot of experience with modelling software and I am wondering does...

14 November 2022 4,483 0 View

Does the Kalman Filter Require Linearity in the Controls?

I'm studying the topic from Probabilistic Robotics by Thrun Burgard and Fox. In the Extended Kalman Filter algorithm, we linearized the action model in the following way. 𝑔(𝑢(𝑡),𝑥(𝑡-1)) =...

23 October 2022 2,352 5 View

In case we feed BWRO (one pass) with 10 ppm total TDS, can we get purified water less than 1 ppm ?

Hi Every one In case we feed BWRO (one pass) with 10 ppm total TDS, can we get purified water less than 1 ppm? Using high rejection Ro membrane , what the side effect to use this...

02 February 2022 1,149 3 View

How to dissolve a lipophilic compund in media?

I am using a lipophilic compunds and used DMSO less than 0.1% to dissolve it and prepared stock solutions out of it.. But when I put the drug in media to be used on the cells, it crystallises. I...

04 October 2021 7,546 1 View

Merging/combined high and low resolution gravity data, is it a challenge ?

I have a gravity data as 500 m interval and another data set as 1500m interval for the same area. what is the best method to combine them without loosing real information ?

28 July 2021 4,604 10 View

How can I transfer the cells seeded in a 96 well plate to eppendorfs ?

I am studying the metabolites of a drug in the cells and their supernatants and for this, I seeded my cells in a 96 well plate with the treatment. Now I want to transfer the cells in Eppendorf to...

01 July 2021 6,762 3 View

Why we used different methods to purification protein ?

pure protein , methods to puried , characterized pure protein

16 November 2020 7,524 3 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

Reversed flow at outlet due to the release of DFBI?

Hi everyone, I am working on a simulation involving restricted canal with ship using DFBI. I am facing reversed flow in my outlet boundaries as the DFBI is released (In 1.25s). Is there any...

17 July 2024 7,032 1 View

Why aren't primary MHD generators with tokamak/stellarator configurations studied/researched?

Magnetohydrodynamic generators are normally used as eihter an attachment to recycle wasted heat and flow of other generators, or used to absorb the energy from rocket thrusters. However, I'm...

24 June 2024 3,949 1 View

Can anyone please let me know which chemistry set I need to use?

Hello everyone, I am working on hydrogen-diesel combustion using a sector mesh in ANSYS Forte with premixed Hydrogen.

14 June 2024 364 0 View

Why does the static pressure at the outlet become a very negative value when the outlet flow boundary conditions are used?

The simulation is for turbulent and incompressible flow and the inlet velocity condition is selected for the inlet

12 June 2024 3,568 2 View

Background on the project topic gender and sports participation in cape coast metropolitan?

an introduction

02 June 2024 520 0 View

How to analyze a speaker box with Comsol?

Airflow Turbulence Air Dynamics Signal effect frequency response

02 June 2024 2,986 1 View

Residuals are getting converged, but at a very migh magnitude of values. Why??

I am running a coarse DNS case for pipe flow with 2.1 Million cells. My residuals are quite fluctuating as its a fully turbulent annular pipe flow case but its getting statistically converged to a...

29 May 2024 2,063 5 View

Can you explain the different subtypes of constipation mentioned in the introduction and their prevalence?

Understanding and Managing Constipation: A Comprehensive Rev... Can you explain the different subtypes of constipation mentioned in the introduction and their prevalence?

24 May 2024 9,279 1 View

Why I should use UDF for modelling hetrogeneous Reaction ?

Hi Everyone, I am using a UDF file that contains coke oxidation of spent catalyst. I was wondering if there is any way to use the built in Function in Ansys instead. Furthermore, coke oxidation...

23 May 2024 4,240 0 View