L-carnitine UV absorbance?

Myn Myb @Myn_Myb

02 February 2018 1 9K Report

Helo

can any body help ! if you 100% correct answer for L-CARNITINE UV LAMDA MAX ABSORBANCE in nm?

Myn Myb

No matter what inee this answer ?

Badges
Science topic

Similar topics
Correction

More Myn Myb's questions See All

my question is in electrochemistry?

If my cell is oxygen clark electrode cell, what is my refrence electrode - working electrode -counter electrode and where does the reaction occurs ,, what is the specific role of each...

10 November 2017 279 2 View

i have a question on UV-VIS?

Drear Dr If iam doing extraction, say using seperatory funnel , and in each wash i need to check for a certain compound that it is going to zero concentration . using UV -VIS and it is no more...

09 October 2017 9,948 3 View

UV-VIS need help ?

Hi Please i need help . if iam doing extraction ! and in every wash , iam cheking the wash by UV_VIS ,, to make sure that material is dissapearring from the solution ? can any please show me How

09 October 2017 6,307 5 View

I have a question in UV-VIS?

Can any one help please , if iam doing solid phase extraction, say usuing sepratory funnel , ineed after each extraction check the wash for a certain compound that its not there any more ie after...

09 October 2017 6,445 0 View

Decomposition of Fe2SO4.7H2O ?

If i heat Fe2SO4.7H2O at 550 c for 5 hrs in open air furance ,, will i get Fe2O3... what if i heat Fe2SO4.7H2O under nitrogen

01 January 1970 7,054 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

Could the "incoming radiation (net radiation)" values be negative?

Could the "incoming solar radiation" values be negative? What is the difference between "global solar radiation" and "incoming solar radiation"? Which one might be measured negative values?

21 February 2021 7,726 9 View

In methylene blue test Why is UV absorbance reading very low as soon adsorbent is added and then increasing before reaching equilibrium?

Hello, I'm working on removal of methylene blue. 01. in the dark test very first reading is taken 15 minutes after adding adsorbent to the dye solution and that UV absorbance reading is very...

19 February 2021 472 5 View