Dear all,
Please I m looking for the shape of the jacobian matrix of axisymetric problem with coupled displacement temperature element using UMAT in Abaqus .
How can I define the jacobian Matrix?
Many thanks for your help.
i recommend you to read ABAQUS manual for the detailed procedure for Jacobian matrix.
how can i calculat jacobian of matrix in matlab?
Actually, I am wondering if I can request the (∆σ)change of stressfor all integration points in Abaqus analysis through Umat ? As I can request stresses and strains and change in strains as...
01 February 2016 2,696 4 View
Dear Researcher, I am wondering if there is a way to change the tolerance of Abaqus . Is that possible? Best regards, Ali
10 November 2015 7,059 4 View
Dear all, I am writing the Abaqus' output such as stress and strain in a text file. I need to use these as training data. However, the results are repeated and given different set of data because...
09 October 2015 9,071 3 View
Dear All, Please I am looking forward to getting the output of an abaqus analysis in a continuous way. I mean I run the input file from Matlab and divide the load for some parts and at each load I...
05 June 2015 2,727 0 View
Dear all, Actually, I am wondering how can I write specific data to a text file via Umat as. I need this data for further purposes? Many thanks for your help
04 May 2015 5,637 10 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...
08 August 2024 6,690 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...
05 August 2024 3,084 6 View
- The Existence/Uniqueness of Solutions to Higher Order Linear Differential Equations - Higher Order Homogenous Differential Equations - Wronskian Determinants of $n$ Functions - Wronskian...
03 August 2024 2,366 0 View
I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...
31 July 2024 9,186 0 View
We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...
31 July 2024 3,900 2 View
I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...
31 July 2024 9,697 0 View