What are state-of-the-art methods/techniques/algorithms for the root-cause analysis of the anomalies?

I have been looking for research articles that target the question "why did an anomaly occur?", however, most of the papers that I found are related to "if an anomaly occurred?". I searched Google...

12 January 2021 7,951 3 View

How to amplify lignin degrading gene?

Hello colleagues, I would like to amply the lignin-degrading gene (i.e., LigX, LigY, LigZ, and LigW) from different types of soil. I have tried to find literature, but unfortunately, there are...

20 October 2020 9,654 3 View

How to remove abnormal behavior at support of FE model of RCC Beam?

Hi, I am modelling a half model of RCC beam in ANSYS Mechanical APDL. The model I have created is exhibiting abnormal behavior at the support with abnormal cracks. I would be grateful if you...

12 October 2020 8,596 3 View

How to calibrate the parameters of coupled damage-plasticity microplane model of concrete for FE modelling of RCC beam in ANSYS Mechanical APDL?

Hi, I am trying to model an RCC beam in ANSYS Mechanical APDL. I have the value of Compressive strength, and modulus of elasticity of the concrete of the experiment I am trying to validate ? Can...

28 August 2020 4,623 2 View

Values for Fouling rate in superheaters and economizers in biomass boilers?

I currently work on analyzing fouling rate in BFB biomass boiler, based on available measurements. Looking through literature, the only reported values I found were from certain TEMA Tables, from...

19 April 2020 1,973 5 View

What is the best methodology to use for development of Mobile Applications?

In Software Engineering the UML is considered a standard way in design of the system. What will be the best in designing the mobile applications?

24 January 2020 5,777 3 View

What are the effects of using powerful magnets around AC current?

I am trying to connect two sockets( sockets being flat surfaces on both sides) using powerful (small sized ~8mm diameter) neodymium magnets with 3 or 4 on each side of the socket so that the pull...

03 January 2020 8,835 3 View

How to determine molecular weight of disordered peptides from diffusion NMR data?

From diffusion NMR (DOSY) experiments, diffusion coefficients are available for ~40 AA disordered peptides. Is there a method to calculate the molecular weights using these data, that is suitable...

08 July 2019 703 3 View

Is there a way to blast a protein against all known proteins to find common epitopes? (Even if they are a couple of amino acids long)?

I read somewhere that some vaccinations result in the onset of a different disease that is due to the fact that the vaccine and another protein inside the body have a shared epitope and are both...

22 October 2018 7,832 3 View

What is the best way to differentiate between efferent and afferent sympathetic nerve fibres immunohistologically?

Efferent as afferent renal sympathetic nerve fibers have a important relevance in the development of cardiovascular disease. Thyrosine hydroxylase is a marker for sympathetic fibers. Is there a...

04 June 2018 4,657 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Isolates of Hymenoscyphus fraxineus?

Dear Dr. Cai, my name is Simone Prospero and I work in the team of Phytopathology at the Swiss Federal Institute for Forest Snow and Landscape Research (WSL;...

01 March 2021 1,133 1 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

Suggestions for occupational stress surveys?

I am currently writing a masters thesis on reasons for occupational stress in the early childhood classroom, and want to include a short survey assessing participants work-related stress levels. I...

24 February 2021 8,678 2 View

The most suitable method to calculate the stress intensity factor in the presence of contact between the crack lips?

I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...

21 February 2021 8,694 4 View

Despite single-cell RNA, how can I characterize a new cell subtype/phenotype?

A new cell subtype was found out only during regeneration phases after a cuprizone-induced demyelination model. How can I characterize this cell? It is important to highlight that was already...

13 February 2021 1,245 1 View

Is there a way in which microglia can be extracted from mice without killing them ?

I'm aiming to use an adoptive cell transfer approach, with microglia in mice with ALS. So far all the protocols I have seen, require sacrificing the mouse. I'd like to re-infuse the microglia back...

11 February 2021 9,509 1 View