It is possible to connect two cohesive planes in Abaqus?

Aditya Nikam @Aditya_Nikam

09 September 2015 1 10K Report

Hello,

I was just thinking if it could be possible to connect two cohesive planes in Abaqus?

Thanks & Regards,

Aditya

Aditya Nikam

Can someone please provide suggestions on above? Will be really helpful! I am really stuck at this point!

Thanks & Regards,

Aditya

Badges
Science topic

More Aditya Nikam's questions See All

Unable to run a ABAQUS model consisting of low permeability value?

Hello All, I was just trying to run a model with pore pressure cohesive elements. When I have the surrounding matrix with low permeability (i.e. of the order of E-15 to E-17 m2) value, the...

08 September 2015 3,838 0 View

Can anyone advice on an Abaqus example problem?

Hello, I am trying to run .inp file and .f file from an example in Abaqus Manual. I have attached link to this question! I have made the necessary changes to be made in the .inp file as per the...

06 July 2015 5,588 16 View

Linking Abaqus 6.14-2 and Intel Fortran?

Hello, I am trying to link Intel Fortran, Visual Studio and Abaqus. I installed as per the below sequence Abaqus 6.14-2 Visual Studio 2013 Community version Intel Parallel Studio XE 2015 Update 4...

05 June 2015 493 3 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How can major oxides determined by ICP-MS/ES be normalized to 100% volatile free? How does this connect with LOI?

I am analyzing cherts from different sources found within one specific geologic formation using ICP-MS/ES. My committee was asking this question about my analysis. I was not sure how to answer this

05 August 2024 7,902 3 View

How do environmental toxins interact with genetic predispositions to increase cancer risk?

I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from experts in the field. If you are an expert or researcher working on...

02 August 2024 2,627 1 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View