Isolation of Propionibacterium acne’s from joint infection ?

12 January 2020 1 1K Report

Please what are procedures related isolation of propionibacterium from joints infection , specific about selective media

Cheng Li

To optimize the microbiological culture methods, preoperative puncture can be performed, and then the synovial fluid was inoculated in aerobic and anaerobic blood culture bottles simultaneously. Blood culture bottles have been previously shown to improve the sensitivity of the detection of microorganisms.

Badges
Science topic

Similar topics
Papers

More Mohammed Younus Taha's questions See All

Protein-aptamer gel electrophoresis help, please??

Hi, I have problems with running gel electrophoresis. I have tried agarose gel electrophoresis and native PAGE. I have two proteins, which have molecular weights of ~30kDa and ~180kDa and two...

03 March 2021 4,275 4 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Expression cloning by using cDNA,do I need to modify the cDNA first?

I am going to have a expression cloning of mammalian gene by using shuttle plasmid to transforming the E.coli However I don't know I should only inserting the Coding sequence ,or I can...

28 February 2021 5,440 3 View

I need dataset for recommandation system?

Hi every body I need to collect datasets from different source to work on recommendation system algorithms, could you advise me how collect data?

27 February 2021 7,063 7 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

How to estimate 2SLS with different instruments for different endogenous variables?

To be specific, I want to conduct an IV regression in stata with the following three equations. EQ1: Y1 ~Y2 Y3 X EQ2: Y2 ~ Z1 EQ3: Y3 ~ Z2 Both Y2 and Y3 are endogenous. However, Z1 and Z2 are...

23 February 2021 6,266 3 View

Which microtomy technique do you suggest for thin and delicate root sectioning ?And, how to preserve and process the roots before sectioning?

We have thin roots of from 1 year old different species of plants. We are looking into anatomical details of the roots. What's the best method to preserve and process the roots once they are...

23 February 2021 1,898 1 View

How to find out the problem of VMD software when i run it?

Hello I try to install and run the VMD software on windows 10 (64-bit).It doesn`t work and it is closed when I run it. I checked all of tutorials, videos and documents. But they did not work...

22 February 2021 8,211 3 View

Can anyone suggest a topic for the Impact of AI and ML in the financial institutions?

I am currently doing my Master Thesis in FinTech and I am thinking of doing my project on the impact of AI and ML on the financial industry but as the impact of these technologies on the industry...

21 February 2021 7,128 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

Can some one help me to find shear stress and normal across middle of the interface along lap length??

i modeled single lap joint using COMSOL Multiphysics software. i wanted to find shear and peel(normal) distribution across middle of the overlap length pls check the image attached

19 January 2021 6,845 3 View

As the extensive research is going on the dissimilar joining of Mg-Ti alloys, what are the exact applications of Mg-Ti joints?

I have extensive literature review related it, but it ends up in automotive, aerospace and energy sector applications, but didn't provided exact applications of Mg-Ti metals joined by welding

28 December 2020 6,621 1 View

For a joint research work, is there any one provide revenue and operating expenditure data on global airline industry for the past two years?

An invitation for a joint research work

22 December 2020 3,720 1 View

Anyone interested in joint work on writing a review article?

I a writing a review article on cancer work through Mathematical modeling. If anyone interested in this work, kindly let me know

13 December 2020 7,585 10 View

FEM modeling of Joints/ Connection?

The attached Joint.png showed and example case of a joint (2 continuum members are connected). There are 3 characteristics of this, 1. There is a Gap: Cause small amount of rigid body rotation and...

07 December 2020 6,603 3 View

Which automatic data processing for angle detection in Plugin Gait (VICON) do you use?

I would like to analyze gait cycles (running) - is there a smart way for cycle detection and calculation of the angles for each joint (average/maximum) for a certain amount of cycles - without...

07 December 2020 2,586 2 View

What software/app can I use to generate annotations for localizing hand joints in an RGB image?

I wanted to know if there is any software/app that helps to easily annotate hand joints in an RGB image manually.

28 October 2020 9,693 3 View

why bodies are passing through each other after force in ansys?

I have line body and surface body in my research and i am doing in Ansys Workbeanch. Spring is line body and other supports are surface body. I joint one end of spring is fixed joint with surface...

17 September 2020 3,270 2 View