Are there any exception like work hardening in metals elastic limit due to dynamic loading?

The samples made out of spring steel are taken from same lot. The specimens were shaped following heating to forging temperature - Forming- Hardening -Tempering methods. After storage of almost 6...

11 February 2021 952 6 View

Regarding to presentation of pairwise comparison of data?

22 January 2021 8,648 1 View

What is the main advantage of using observer based fault tolerant controller(FTC) for sensor fault tolerance?

I am working on FTC for handling sensor faults in the system. I have read about observer-based FTC schemes which use error threshold-based logic between the states and estimated states. If a...

10 January 2021 5,771 2 View

Can a luenberger observer (even a modified version) be effective for a nonlinear affine system?

I want to know whether a luenberger observer or a modified form of it be effective for estimating the states of a system of the following forms: 1. x_dot = f(x,u,d); y = x 2. x_dot = f(x,u); y =...

20 December 2020 1,392 4 View

How much Tensile strength and hardness can be acheived in Aluminium 7050 MMC with B4C reinforcement?

I have conducted research on characterisation of Al7050 + B4C by electromagnetic stir casting. The alloy employed in the process is casted alloy and the Composite too is casted. How much strength...

16 November 2020 9,226 3 View

Why whitefly prefer not to infest Pigeonpea?

Whitefly, Bemisia tabaci is pest of broad host range. In pulse crops, it generally infests greengram, blackgram and cowpea but not Pigeonpea. There might be some biochemical or morphological...

09 November 2020 9,199 3 View

Can u suggest how to identify the matrix material and reinforcement particle distribution in the MMC of scanning electron miroscopy (SEM) images?

How to identify the reinforcement particle behavior in SEM images

09 November 2020 8,664 3 View

Can someone help me in designing off-MPPT mode in a Standalone DC Microgrid?

I am working on voltage control of a Standalone DC Microgrid consisting of Single PV source, a battery and loads. The PV is interfaced through Buck converter to the DC bus, the battery is...

01 October 2020 7,071 2 View

Modeling pure shear loads in Abaqus?

I am trying to simulate a pure shear loading on a cubical block with a single brick element. While I am simulating the other stress components are not getting zeros. Can anyone suggest to me how...

22 September 2020 7,649 3 View

Can anyone suggest any introductory book on tensor analysis and tensor calculus for continuum mechanics?

I have searched google. But it would be more helpful to get suggestions from personal experience.

14 September 2020 5,426 5 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

How to polymerize TEOS?

I want to polymerize TEOS on a surface. I know that NH4OH is a preferred catalyst and an alcoholic solvent should be used .But I can not find certain amounts of each material to use. Does any one...

02 March 2021 1,404 6 View

Ester cleavage conditions?

Hi all, I need to cleave the ester in Ethyl 2-amino-1H-imidazole-5-carboxylate to make the carboxylic acid and retrieve the product from solution to use in downstream applications of linking to...

01 March 2021 8,766 3 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View