I want to print two models with Aluminum metal, and I am looking for printing space about 50cmx3cm3cm or more than 50cm.
Contact Intechadditivesolutions located at bangalore, india.
Dear Mr. Jarullah,
Materialise or 3D systems, I had good experiences with these companies before.
Quality: It would help to tell us what tolerances you need.
Price: goes hand in hand with quality, maybe share a price your expect.
Try Ortho-Baltic in Vilnius Lithuania
+37037473970 Ignus
Good luck
Thanks for all of you,
Mr. Detlef jannes, I have walls with thickness about 5mm in my geometry. actually kind of complex Geo. inside circular pipe. Also, Is there a machine which can print with length about 50cm or more, whether the metal is copper or Aluminum.?
22 February 2021 2,588 2 View
We have a research project consisting of three variables where big data is the independent variable. Some previous studies showed that Volume, Variety, Velocity and Veracity Are the dimensions...
21 February 2021 8,133 2 View
I have a direct band gap material and an indirect band gap material. If I made a composite of both through physical mixing. Then how can I determine the band gap of such a material as the Tauc...
17 February 2021 8,104 4 View
Hope so, you are all fine, I want to perform EIS and CV of my material Carbon doped Titania as a counter electrode for DSSC, I just want to know what electrolyte solution and in what molar...
25 December 2020 7,095 3 View
Hi, I am going to execute an experiment with the four categorical variables (A=2 levels, B=2 levels, C=2 levels, D= 5 levels) and one dependent continuous variable. There are total of 40 groups...
19 December 2020 3,600 4 View
I want to introduce my manuscript to journal which is not take fee on publishing.
15 November 2020 609 3 View
Dear All, Here I have an interesting question that comes to me about crystallographic planes and growth rate. The literature survey shows, the (100)-oriented crystals the crystallographic plane...
06 November 2020 9,490 10 View
A-site deficient 0.1BiScO3-BaTiO3 (BSBT) thin films were deposited on Pt/TiO2/SiO2/Si substrate by using PLD. XPS results revealed that A-site vacancies increase with the increase of deposition...
05 November 2020 9,281 1 View
Could you make some points about the difference between Data-Driven Adaptive Robust Optimization and (classic) Adaptive Robust Optimization?
01 November 2020 9,653 3 View
I want to know about the dangling bond? by which method we can find it, does its need some special type of characterization just like XRD etc... or method i want to find dangling bond effect in...
26 October 2020 1,938 6 View
We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...
03 March 2021 7,975 3 View
Hi everyone, I'm studying Marketing and I would like to write my PhD thesis on the topic of pricing. Any specific ideas?
02 March 2021 9,706 5 View
Warm greetings! My name is Ayichew S. and I am doing my Ph.D. in Medical Microbiology focusing on Human papillomavirus). At this stage, I have almost completed a clinical sample (Cervical swabs)...
25 February 2021 3,612 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.
22 February 2021 1,410 1 View
08 February 2021 7,901 6 View
Our manuscript was published ahead of print. The edited and revised version is now available. How do I remove the old version of the manuscript from the research gate?
01 February 2021 5,965 1 View
my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?
01 February 2021 7,140 4 View
As suggested in the title I want to image my DNA nanoflowers/origami using SEM. These nanoparticles are an organic-inorganic particle made out of highly packed DNA and also contain magnesium...
28 January 2021 3,343 3 View
19 January 2021 3,792 3 View