Is there any valuable study about modeling of masonry buildings?

02 February 2018 0 9K Report

Badges
Science topic

Similar topics
Engineering
Modeling

More Muhammed Abbas Husain's questions See All

What is the basics for team work to be active in scientific research works?

Scientific research work usually needs woorking as a team for all stages of research. What is the basics for team work to be active in scientific research works?

02 March 2018 8,746 5 View

Why the ASTM - A325 bolts with over 1 inch diameters have tensile stresses less than those for bolts with 0.5 - 1 inch diameter?

02 March 2018 5,196 0 View

What is the latest excellent software for graphing equations or relations of research work outputs?

01 February 2018 353 0 View

Is there any appropriate website for learning ABAQUS software?

01 February 2018 6,738 1 View

What are the most considered softwares in designing the steel connections?

There are a lot of softwares concerning with the design of connections in steel structures. What are the most considered softwares between them?

01 February 2018 2,363 0 View

What is the criteria of software to be accepted in scientific research?

Nowadays there are a lot of softwares which are used to simplify working and calculations in scientific researches. Are there any guidelines to choose the appropriate software so as working by...

31 December 2017 5,519 0 View

Is Wikipedia considered to be an acceptable reference in scientific researches?

Acceptance of Wikipedia as a reference or bibliography in scientific researches.

31 December 2017 3,701 2 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View