Is there any softare/code to automatically identify cyclic voltammetric peaks?

More Kenichi Shimizu's questions See All

Where do the electrons that are blown off the atoms by X-rays reach?

When studying EXAFS and XPS, I often see that "X-rays bounce electrons from atoms". Where will the electrons that are blown off the atoms by X-rays eventually go? In the case of EXAFS, I think...

11 January 2021 1,681 3 View

How can you perform electrochemical impedance?

Dear everyone I would like to perform the electrochemical impedance during the redox reaction of the positive electrode active material. I have three questions. 1. Why should the electrochemical...

10 January 2021 1,204 2 View

How can you identify and quantify substituents on the MOF surface?

Dear everyone, Currently, I am studying changes in the surface physical characteristics of MOF, which is a mixture of terephthalic acid and 2-aminoterephthalic acid in an arbitrary ratio....

08 January 2021 5,870 2 View

Difference in meaning between charge transfer resistance and activation energy (thermodynamic or kinetic?)?

Dear everyone, I have a question about the difference between the charge transfer resistance and activation energy obtained from the electrochemical impedance of the secondary battery. As...

23 December 2020 6,446 2 View

Why is the initial voltage of a lithium metal battery around 3 V?

Dear everyone, I have a question about the difference in the initial voltage of a battery that uses lithium or graphite as the negative electrode. The voltage of a battery with lithium metal...

23 December 2020 4,096 1 View

How two melting peaks in DSC of polypropylene can be merged into one crystallization peak?

The figure shows DSC cooling (blue) and 2nd heating (green) curves (step: 10 K/min) for a commercial sample supplied as Atactic Polypropylene (APP). The heating curve illustrates two major...

03 March 2021 5,857 3 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

What information can be had from raman at higher wavenumber?

i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...

26 February 2021 2,499 1 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

How can I find a Raman spectrum wavenumber corresponding to what compound?

I have several Raman spectra with very distinct peaks at certain wavenumbers, such as 277, 359, 466, 583, 623, 686, and 795cm-1. How can I identify them to what compound(s)? The RRUFF and others...

24 February 2021 363 3 View

Genescan gives 3 peaks instead of one?

Hi all, I am doing a genescan analysis for a deleted exon in the patient sample. The amplified region is 215 bp. In the patient sample because of homozygous deletion, no peak is observed while in...

23 February 2021 5,645 1 View

Why the CHi^2 is close to zero with a bad fitting but the Rp and Rwp are still high?

I am refining my XRD data using in FullProf program. The intensity of the modulated X-ray peaks is almost flat. I tried to adjust the peak intensities but unsuccessful. What is the reason? I guess...

23 February 2021 2,304 4 View

Are there methods for automatically mapping floodplains, fans and terraces?

I want to map these river geoforms with as little subjectivity as possible. I have a high resolution DEM generated by drone data.

22 February 2021 7,800 3 View

Can't recognize exact phase and PDF card no of Silicon carbide in XRD?

We have deposited silicon carbide on carbon substrate using one PVD technique. Due to amorphous behavior of SiC at low deposition temperature, we performed heat treatment of those films at...

22 February 2021 2,072 3 View

Raghav G R

Yes it can be automatically identified through Biochem bio logic electrochemical workstation. You can download a demo software from the website.

Kenichi Shimizu

Thank you, I will check it out. Though, I was hoping that we do not have to convert/export file into another format.

Yes it has option to open files from various electrochemical workstation.

Ahmad Keshavarzi

Article eL-Chem Viewer: A Freeware Package for the Analysis of Elect...

hello dear

‘eL-Chem Viewer’, is useful for the analysis of asymmetrical and amperometric data, and enables their post-acquisition processing using semi derivative, semi-integral, derivative, integral and elimination procedures.

@ Michelle Tokarz

eL-Chem Viewer: A Freeware Package for the Analysis of Electroanalytical Data and Their Post-Acquisition Processing