Is there any Simulink model of Inverse MR Damper is available?

01 January 1970 1 2K Report

Is there any Simulink model for Inverse MR damper is available?

Or any simple Inverse MR damper model which can be easily created Simulink.?

I am looking for simple inverse MR damper model (e.g inverse bigham or inverse bouc wen) without neural network. Also Simulink model of inverse MR damper.

Non parametric inverse model will also be good and easy.

Badges
Science topic

More Pankaj Sharma's questions See All

Why given matlab program is giving error? How to run it and give input to it?

I have simulation data of sprung mass acceleration (A) vs time (t) in vertical direction for quarter car model. The data is taken as output from “to workspace” block of Simulink. I want to convert...

06 July 2019 5,538 9 View

How to Plot Real Amplitude vs Frequency (Hz) plot by Simulink Block? Why my model is not generating the correct graph?

I have simulated a 2DOF Quarter Car Model (Figure Attached) for Step Input of 0.1m. The Weighted RMS acceleration obtained is 4.768 m/s2 . The Acceleration plot on Time Scale is also attached. I...

05 June 2019 5,436 3 View

What's wrong with my Fuzzy Controller?

My Fuzzy Controller is responding very slow, what is the reason. Do scaling factor is must for fuzzy. Is there any method to find scaling factor? Really frustrating slow response of fuzzy.

02 March 2019 9,672 3 View

What’s wrong with my Matlab Code? No idea whether to solve it in this way or by any other better method?

I am preparing the matlab codes for below mentioned seven interlinked equations: A = Ga * SI (1) OC = Goc*SI (2) SI = 2*t (3) ES= 3*t (4) dGa/dt = (alpha*SI)* (ES-A) (5) dGoc/dt = (betaa*SI)*...

10 November 2018 3,013 3 View

Which Simulink Block is Right Continuous RMS or RMS for Automotive Suspension Sprung Mass Acceleration in Given Solution?

A 2DOF Simulink Model Under Step Input of 0.1 m (Bump) is simulated as shown in figure attached. The continuous RMS block is used to find RMS value and stabilises at value of 0.9 m whereas simple...

08 September 2018 3,894 0 View

What will be Random Number Values for Given Simulink Model of Random Road Profile Generator?

Research Paper Attached here discuss about Simulink Model of Random Road Profile Generator . The Model has Simulink Block of Random Number, how this Random number values will be calculated for...

06 July 2018 5,645 0 View

How can we calculate height of PSD for white noise?

I know the value of PSD of a white noise, I need to calculate height of PSD to put that value in Band Limited White Noise block of Simulink. How to calculate Height of PSD?

06 July 2018 9,409 4 View

How to Calculate Input values of Similink Road Profile Generator block Band Limited White Noise or Random Number?

My Simulink Model is not generating Random Road Profile as Per ISO 8608 for road Class-D. How to calculate or find values of Random Number Block, Fig.1 and Band Limited White Noise, Fig.2.

06 July 2018 9,238 0 View

What;s wrong with my matlab code to solve given equation?

how can I solve this equation by ode45 matlab code? Here z and zdot vary with time (t = 0:0.02:3) and simulation is also made for 3 seconds. My code gives answer different than that of Simulink...

05 June 2018 8,281 7 View

How to give input to given Matlab script for ISO 2631 frequency weighted acceleration in vertical direction?

01 January 1970 455 1 View

How to simulate a varying three-phase load /load profile in Simulink/MATLAB?

I have a Simulink model that connected a main utility (AC-grid) with a three-phase load changing from 20kW to 100kW in 5 seconds and I don't know how to build this load in Simulink. Please your...

14 July 2024 8,892 3 View

Dear Professor/Researcher, I want to use LoRa to send a signal with a frequency of 10 kHz. Is this feasible or not?

I use LoRa with Matlab/Simulink

23 June 2024 3,847 3 View

Aspen Adsorption linking to MATLab ??

Hi, I am looking to link MATLAB to Aspen Adsorption. I know that for Aspen Plus, it is possible to use actxserver(). Does anyone know if the same method can be used for Aspen Adsorption as well?...

20 June 2024 8,338 2 View

Does anyone know where this module is in Simulink?

I try to build a three-phase wireless power transmission model and saw this module in an article.

27 May 2024 3,471 2 View

Can you help me for do this matlab simulink project?

I'm new. I know just little use of matlab. Help me for do this matlab simulink project.

25 May 2024 4,247 1 View

Simulink model for ANC earmuffs?

Adaptive Filters are core of the ANC system. They continuously adjusts its filter coefficients to minimize the error signal, effectively generating the anti-noise signal. Common choices include...

21 April 2024 4,468 1 View

I need help designing an H Infinity controller to control a wind energy conversion system ?

What is the best approach to design an H infinity controller for a linear model of a wind energy conversion system, with the goal of simulating it in Simulink? Any specific methods or tools...

26 March 2024 4,008 1 View

Any suggestions to implement TECS on MatLab/Simulink?

Hi, I am trying to implement the TECS core algorithm to my closed-loop 3DoF model of the aircraft in MatLab/Simulink. The tuning of the innermost loops was accomplished succesfully, but now I am...

17 March 2024 8,446 1 View

Who has work on droop control for grid forming ??

could we make grid forming as stand alone inverter and control it by add active power ref and frequancy and voltage for rl load ? who has work on it in matlab simulink ? for me i did it for rl...

11 March 2024 6,303 0 View

Find a controller for a feedback-loop?

My team and I are working on an automation project to stabilize the altitude of an airplane. However, we've encountered an issue that seems unsolvable for us, at least for the moment, in the final...

03 March 2024 7,659 0 View