Is there any research that quantitatively states the impact of microfibers on rate cement hydration ?

Souradeep Gupta @Souradeep_Gupta2

12 December 2015 1 5K Report

For example, does addition of PP fibers by 2-4% volume fraction affect early hydration of concrete?

Doha M Al Saffar

PP fiber improve physical behavior agenst tensile stress...etc., so dont affect on chemical reactions.

Best wishes

Badges
Science topic

More Souradeep Gupta's questions See All

Is there any study that shows calcite precipitated by bacteria in self-healing concrete lead to micro-cracking?

Calcium carbonate precipitated by bacterial metabolism is the sealing agent for cracks in self-healing concrete. However, if there is no crack, would the calcite generated by bacteria lead to...

08 September 2017 5,576 1 View

Is there any published data on relationship between adiabatic temperature rise during cement hydration and heat of hydration?

I am looking for an equation or model that draws relationship between temperature rise of cement paste and heat of hydration of portland cement.

04 May 2017 5,421 3 View

Is there any data on water absorption capacity of biochar in alkaline solution?

Will water retention capacity of biochar be affected if highly alkaline water is used (pH>12) as absorbate instead of normal water?

01 February 2017 4,209 3 View

What are the explanations for balling of polypropylene fibers in mortar/concrete?

Any studies that discuss the possible reasons for this balling effect?

11 December 2016 9,116 0 View

Effect of carbon particles (30-80 micron) on internal temperature of concrete during hydration?

If I mix carbon particles ( size 30-80 micron) in cement , what will be the effect on internal concrete temperature during first 24 hours of hydration ?

10 November 2016 7,274 3 View

What kind of carbonate polymorphs may be present in saw dust derived biochar prepared at 300 degrees?

I have prepared biochar from mixed wood saw dust at 300 degrees. XRD pattern show sharp peaks at 2-theta = 37.8 , 44.06, 64.38 and 77.5. Does it say anything about presence of calcium carbonate...

10 November 2016 4,338 9 View

How does cohesion between a carbon based admixture and cement/sand particles affect setting time of mortar?

The carbon rich admixture is hydrophilic. By absorption of free water the admixture can reduce initial setting time but how does the bonding between this admixture and cement affect setting time?

10 November 2016 3,629 2 View

Are there studies on relation between hydration and microstructure of mortar/cement paste and pH of mortar/concrete?

Specifically, I would like to ask whether some research have explored the rate of hydration, strength development and hydration products when the pH of concrete or mortar drop below 12 or even 10 ?

07 August 2016 9,900 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

How to get LP fiber modes directly from Comsol?

Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...

23 July 2024 4,019 3 View

Sample size for qualitative study?

I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...

20 July 2024 9,153 11 View

Liposome Preparation using Heating Method - Why does my liposome suspension form aggregates?

Hello everyone, I am trying to encapsulate an essential oil in the liposomes using the heating method and encountering some issues. I am following the protocol described below, but my solution...

10 July 2024 4,083 3 View

Zero pivot in Abaqus concrete 3D printing simulation using model change?

Recently I've been working on a simulation of concrete 3D printing, and has successfully simulated a layer-by-layer 3D printing process using model change. However, when I proceeded to try...

06 July 2024 2,130 0 View

How to solve Bubble Error in fiber splicing?

I'm having a bubbling error while splicing 100/350 um optical fiber (core/cladding) on the Fujikura FSM100P+. I have tried some ways such as changing Prefuse power and Prefuse time but to no...

03 July 2024 7,463 6 View

What heavy aggregates are available for protective concrete in your country?

01 July 2024 1,625 3 View

Poured Earth Concrete ?

What are the benefits and advantages of concrete flooring when used in parking lot floors, and what are the technical requirements and general specifications that should be considered to ensure...

29 June 2024 2,171 5 View