How to add an Adversary in omnet++ and to find hopCount from source to Sink node using Omnet++?

i want to calculate hop count from source to sink node in omnet++ and want to add an adversary which will move when it analyze some packets transmission. for instance i am not using any omnet++...

10 November 2015 7,792 1 View

Which omnet++ simulator should i use for wireless sensor network?

i want to simulate a wireless sensor network having different wireless nodes which will be connected to each other on the basis of some condition. i want to calculate the distance between nodes...

10 November 2015 6,648 1 View

How do I calculate energy consumed in WSN simulation in Omnet++ without using Omnet++ Models e.g. Castalia,Mixim, INET etc.?

10 November 2015 6,626 4 View

How to create Connectionless Nodes in omnet++?

i want to create some nodes in my sensor network using omnet++, which doesn't have a connection with other nodes, so how can i do that?

09 October 2015 3,745 0 View

No title

dear Friends!i am a Computer Science Scholar and my research area is Wireless Sensor Networks. i am studying an article on privcy in Wireless Sensor Networks in which the author have used an...

07 August 2015 9,194 5 View

Need help in omnet++?

Hello everyone! I want to send data packets from a source to sink through different routes i.e. A packet is sent on route1, packet B is sent on route2 and so far.... i want to do this in omnet++...

05 June 2015 349 0 View

Which simulator should I use for source location privacy preservation in wireless sensor networks,e.g Omnet++,Castalia,Mixim,or Inet?

03 April 2015 4,543 3 View

Any help on the selection of omnet based Simulating model?

i want to create a wsn and then want to calculate residual energy of each node,distances between nodes,distance from sink node, for doing this task which simulation model should i use,...

02 March 2015 8,229 2 View

How can I create wireless sensor network in omnet++?

i want to create a wireless sensor network with a source node,intermediate nodes and sink node with multiple paths from source to sink through intermediate nodes. The problem which i am facing is...

02 March 2015 1,607 6 View

How to link castalia and omnet++ in ubuntu 64 bit?

i have successfully installed both Castalia and omnet++ in ubuntu 64bit but now dont know how to link them and start working on it please guide me step by step.please provide me some book or...

01 February 2015 2,183 0 View

SDS page software for analysis?

I did sds page to determine the difference in protein expression between 3 types of vaccine , but i don't have scanner or densitometer available. . so i wonder if there is a software to analyze...

02 March 2021 6,270 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

What are the patterns of human behavior that lead to COVID-19 infections?

Does data from contact tracing help in establishing patterns of behavior and social interactions that lead to infections? There are cases here in the Philippines where patients have no travel...

25 February 2021 9,002 13 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View