Is there any professor who needs a PhD candidate to work under his/her supervision?

I have completed my Master's (18 years) in Computer Science with two Research articles, and now looking forward to starting my Ph.D. under the kind supervision of a professor who is working on...

09 October 2017 8,551 2 View

How to add an Adversary in omnet++ and to find hopCount from source to Sink node using Omnet++?

i want to calculate hop count from source to sink node in omnet++ and want to add an adversary which will move when it analyze some packets transmission. for instance i am not using any omnet++...

10 November 2015 7,792 1 View

Which omnet++ simulator should i use for wireless sensor network?

i want to simulate a wireless sensor network having different wireless nodes which will be connected to each other on the basis of some condition. i want to calculate the distance between nodes...

10 November 2015 6,648 1 View

How do I calculate energy consumed in WSN simulation in Omnet++ without using Omnet++ Models e.g. Castalia,Mixim, INET etc.?

10 November 2015 6,626 4 View

How to create Connectionless Nodes in omnet++?

i want to create some nodes in my sensor network using omnet++, which doesn't have a connection with other nodes, so how can i do that?

09 October 2015 3,745 0 View

No title

dear Friends!i am a Computer Science Scholar and my research area is Wireless Sensor Networks. i am studying an article on privcy in Wireless Sensor Networks in which the author have used an...

07 August 2015 9,194 5 View

Need help in omnet++?

Hello everyone! I want to send data packets from a source to sink through different routes i.e. A packet is sent on route1, packet B is sent on route2 and so far.... i want to do this in omnet++...

05 June 2015 349 0 View

Which simulator should I use for source location privacy preservation in wireless sensor networks,e.g Omnet++,Castalia,Mixim,or Inet?

03 April 2015 4,543 3 View

How can I create wireless sensor network in omnet++?

i want to create a wireless sensor network with a source node,intermediate nodes and sink node with multiple paths from source to sink through intermediate nodes. The problem which i am facing is...

02 March 2015 1,607 6 View

How to link castalia and omnet++ in ubuntu 64 bit?

i have successfully installed both Castalia and omnet++ in ubuntu 64bit but now dont know how to link them and start working on it please guide me step by step.please provide me some book or...

01 February 2015 2,183 0 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View