i try to find the history of Cork Film Festival
I am a bit confused. I am planning an experiment in the field where fish will be caught by electrofishing. Afterwards, they are supposed to be euthanised by using an anaesthetic. I found...
10 February 2021 1,101 4 View
I'm currently doing a research project on the effectiveness of U.S. aid in Georgia, and would very much appreciate your insights.
22 December 2020 4,189 1 View
I'm looking for ways to functionalise a material with a cell-adhesive peptide (relatively short chain - 6aa) and I was just wondering if peptides can withstand high temperatures (100-150 C) for 30...
15 January 2020 8,978 4 View
Hi! I've been running qPCR on some drinking water samples with a primer/ probe FAM assay. In any given run, there have been at least a few samples with artificially high fluorescence reads,...
16 October 2019 8,060 3 View
Several studies mention using agar amended with mercuric chloride when isolating mercury resistant bacteria. Is there a lab method available for preparation of these plates? If no, what are some...
17 June 2019 5,047 5 View
30 January 2019 5,443 4 View
Subconscious, subjective drivers.
22 January 2019 5,397 5 View
The cells look healthy after thawing, but they die when I try to split them. I have tried making fresh media and fresh matrigel, and have tried filtered and non-filtered Accutase. Does anyone have...
19 December 2018 630 9 View
I tried to dechorionate embryos with pronase at 1mg/mL. I made 3 washes but I obtained a high mortality rate and the medium was dirty. Thank you for your answers
03 January 2017 3,455 4 View
Sustrate=BAPNA I get a white solution when i mixed BAPNA(with DMSO) and buffer Tris-HCL/CaCl2 First 3 minutes the activity goes down, after 3 min stars to go up but slowly. Is this normal?
25 July 2016 6,718 7 View
We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...
03 March 2021 7,975 3 View
I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?
01 March 2021 930 3 View
Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.
28 February 2021 3,640 3 View
24 February 2021 2,362 5 View
Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...
24 February 2021 3,785 3 View
I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...
22 February 2021 5,324 3 View
Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...
21 February 2021 6,197 1 View
The regenerated cellulose film was prepared by zinc chloride/H2O system. The zinc chloride had been washed away in the regeneration process, and the wet film which was not dried had uniform...
18 February 2021 9,538 1 View
what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....
17 February 2021 8,987 5 View
Hello All! I'm trying to model a contact between a coated substrate and a tip in Abaqus. The coating is ultra-thin compared to the geometry of the substrate. So I defined the coating using the...
16 February 2021 1,594 3 View
