I need to make a motion device that works in MRI which means that the stepper motors need to function well under static and gradient magnetic fields. Are there any recommendations for such commercially available stepper motors?
Hi, I have problems with running gel electrophoresis. I have tried agarose gel electrophoresis and native PAGE. I have two proteins, which have molecular weights of ~30kDa and ~180kDa and two...
03 March 2021 4,275 4 View
Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...
02 March 2021 4,624 4 View
I am going to have a expression cloning of mammalian gene by using shuttle plasmid to transforming the E.coli However I don't know I should only inserting the Coding sequence ,or I can...
28 February 2021 5,440 3 View
Hi every body I need to collect datasets from different source to work on recommendation system algorithms, could you advise me how collect data?
27 February 2021 7,063 7 View
To be specific, I want to conduct an IV regression in stata with the following three equations. EQ1: Y1 ~Y2 Y3 X EQ2: Y2 ~ Z1 EQ3: Y3 ~ Z2 Both Y2 and Y3 are endogenous. However, Z1 and Z2 are...
23 February 2021 6,266 3 View
We have thin roots of from 1 year old different species of plants. We are looking into anatomical details of the roots. What's the best method to preserve and process the roots once they are...
23 February 2021 1,898 1 View
Hello I try to install and run the VMD software on windows 10 (64-bit).It doesn`t work and it is closed when I run it. I checked all of tutorials, videos and documents. But they did not work...
22 February 2021 8,211 3 View
Secretory universal influenza antibody CR9114 were successfully expressed by adenovirus vector ,then we used protein A G beads purify CR9114.But the molecular weight of the purified antibody under...
22 February 2021 4,318 2 View
21 February 2021 3,417 5 View
About crack modeling in ABAQUS: Mode I (pure-tensile cracking) and Mode II (pure-shear cracking), these assumptions may be accruing in theoretical approach (ABAQUS) not practical in Lab....
19 February 2021 6,156 1 View
I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...
03 March 2021 1,931 5 View
I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...
02 March 2021 1,408 1 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...
26 February 2021 1,511 3 View
Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...
25 February 2021 8,749 6 View
I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...
23 February 2021 9,592 2 View
I am working on single trial motor imagery data i.e. EEG data. I am following a paper which has a dataset from BCI challenge IV (dataset 2b). After removing noise and extracting all the data from...
23 February 2021 5,503 1 View
As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...
23 February 2021 3,175 3 View
Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?
22 February 2021 2,968 1 View
I am thinking of electrifying the street food carts while harvesting energy using solar panels on top.
22 February 2021 4,323 3 View