Is there any Mg-Cu based alloy,where Mg is solvent?

Hemant Nautiyal @Hemant_Nautiyal2

07 July 2016 1 9K Report

If there is any can i have research paper on it and the procedure to make it,along with the properties of it.

Saman Mostafapoor

Dear Hemant

search for this article:

"High damping capacities of Mg-Cu based alloys"

Authors:WAN Di-qing, HE Bo-lin, XIONG Guang-yao and ...

And this one:

"Biodegradable Mg-Cu alloys with enhanced osteogenesis, angiogenesis, and long-lasting antibacterial effects"

Authors: Chen Liu, Xuekun Fu, Haobo Pan, Peng Wan, Lei Wang, Lili Tan, Kehong Wang, Ying Zhao, Ke Yang & Paul K. Chu

The links are added to the answer.

http://www.sciencedirect.com/science/article/pii/S100363261060516X

http://www.nature.com/articles/srep27374

Badges
Science topic

More Hemant Nautiyal's questions See All

How I can measure the contraction and expansion of graphene nano particles reinforced in Copper matrix composite?

I have sintered Copper matrix composite which is reinforced by graphene, since graphene shows negative thermal expansion upto a certain temperature and copper shows positive thermal expansion...

01 February 2018 4,772 1 View

How we can measure the Tensile Strength of a Pellet?

We have a pellet of size 30 mm diameter and 6 mm. thickness,it is a metal matrix composite, how i am supposed to measure the tensile strength of it, by which machine or facility or method it can...

06 July 2017 4,036 5 View

What material balls ,ball size and for what time should we conduct the ball milling operation of PMMA beads or granules to convert it in powder?

i want to convert the PMMA( poly methyl methaacrylate) 2 mm beads into fine powder of 50 micrometre by the means of ball milling what material ball should i use so that it should not react to PMMA...

09 October 2016 8,623 3 View

How to increase wetability of interface in MMC?

In order to increase the wetability of particulates and matrix what should we do,need the literature regarding this.

06 July 2016 8,702 0 View

What are the things to be taken care of while fabricating a composite?

If we want to fabricate a composite to serve a definite purpose,what approach we should have in the selection of its constituents,in the other words how we can estimate the properties of a...

06 July 2016 8,337 10 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Best mask design for metal deposition aiming build a Perovskite solar cell device?

What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?

31 July 2024 4,835 3 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View