How we can measure the Tensile Strength of a Pellet?

We have a pellet of size 30 mm diameter and 6 mm. thickness,it is a metal matrix composite, how i am supposed to measure the tensile strength of it, by which machine or facility or method it can...

06 July 2017 3,893 5 View

What material balls ,ball size and for what time should we conduct the ball milling operation of PMMA beads or granules to convert it in powder?

i want to convert the PMMA( poly methyl methaacrylate) 2 mm beads into fine powder of 50 micrometre by the means of ball milling what material ball should i use so that it should not react to PMMA...

09 October 2016 8,539 3 View

How to increase wetability of interface in MMC?

In order to increase the wetability of particulates and matrix what should we do,need the literature regarding this.

06 July 2016 8,606 0 View

What are the things to be taken care of while fabricating a composite?

If we want to fabricate a composite to serve a definite purpose,what approach we should have in the selection of its constituents,in the other words how we can estimate the properties of a...

06 July 2016 8,257 10 View

Is there any Mg-Cu based alloy,where Mg is solvent?

If there is any can i have research paper on it and the procedure to make it,along with the properties of it.

06 July 2016 9,277 1 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

What is Nano technology with coronavirus helpe the human..and is it nano mterals removal of covid19?

I anwar by adsorption or reaction ..but it is either more method...

02 March 2021 4,811 2 View

How to compare different concentrations of nanoparticles for characterization from ICP-MS?

I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...

02 March 2021 7,626 1 View

Discrete Phase model (DPM) particle break-up has particle size limits during particle tracking?

Hello, I am currently working on simulating water droplet partciles in a closed room. When I use uniform particles, without "particle break-up", I can carry out the simulation without any problem....

02 March 2021 3,053 2 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Distribution of particles in metal matrix?

How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...

28 February 2021 7,397 8 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View