Which is the best place in the world for the plant biotechnology research?

I am searching for a good place for the Post Doc,

02 March 2021 4,053 3 View

What is the difference between positivism and post positivism?

Your comments are being sought in regard of research methodology. Could you explain the meaning of postivist and positivism. How post positivism is different than the positivism?

26 December 2020 8,614 4 View

How to find APC without open access choice in hybrid journals. ex springers ?

I was going through springer journal websites and only APC for open access is given. But I would like to know the cost of publishing without open access choice in hybrid journals. So how to find...

18 September 2020 5,861 3 View

Can we calculate the average value of the particular sub-region of Raster TIFF image?

1) I have calculated various Drought Indices for all the 26 Mandals of the Warangal Region India. Can I calculate the average value of a particular drought index in any sub-region directly by...

19 April 2020 1,127 7 View

Is it possible to establish the relation between the Remote sensing based Vegetation Index and on field Crop area sown Data?

I calculated vegetation indices (MSI, NDVI, NDWI, NMDI, SWCI) for the Warangal region of India from 2014 to 2019 (May month) by using Landsat8 data. I got the on-field data of crop area sown from...

17 April 2020 1,943 2 View

How to apply deep learning for estimation of various parameters in single carrier system?

Parameters like carrier frequency, symbol timing offset and symbol rate estimation in a single carrier system.

23 February 2020 2,980 4 View

Cosine Similarity between columns of two dataframes of differing lengths ?

Hi All I have text column in df1 and text column in df2. The length of df2 will be always > length of df1. I want to calculare cosine similarity for every entry in df1[text] against every entry...

30 December 2019 7,453 1 View

How to perform antiferromagnetic DFT calculations?

There are three types of antiferromagnetism, namely A , C and G type. I want to perform DFT calculations with these types of antiferromagnetism using either Quantum Espresso or Wien2K codes in...

24 October 2019 7,175 3 View

Standard dose of lead acetate creating testicular toxicity and route of administration?

Hello everyone i read number of articles but everyonechoosed diffirent dossage and route of administration but which is the best dossage creating testicular toxicity in rats and route of...

25 September 2019 7,177 3 View

Can we use MAPLE or MATLAB to get numerical solution for coupled second order nonlinear differential equations?

I need this to study blade vibration.

07 May 2019 8,338 11 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

What is the best way to keep an anaerobic chamber anoxic in the absence of hydrogen?

I'm a graduate student who works with an anaerobe, so I often work in an anaerobic chamber. I've been working on an assay that involves the steady-state of the quinone/ quinol pool. Anoxic...

03 March 2021 2,971 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View