Arruda-Boyce(8-chain model) UMAT availability?

Dushyanth Rudra Mahesh Velugubantla @Dushyanth-Rudra-Mahesh-Velugubantla

13 March 2024 0 3K Report

Can someone provide Arruda-Boyce(8-chain model) UMAT code for Abaqus?

Badges
Science topic

Similar topics
Filing

More Dushyanth Rudra Mahesh Velugubantla's questions See All

Which is the best place in the world for the plant biotechnology research?

I am searching for a good place for the Post Doc,

02 March 2021 4,053 3 View

What is the difference between positivism and post positivism?

Your comments are being sought in regard of research methodology. Could you explain the meaning of postivist and positivism. How post positivism is different than the positivism?

26 December 2020 8,614 4 View

How to find APC without open access choice in hybrid journals. ex springers ?

I was going through springer journal websites and only APC for open access is given. But I would like to know the cost of publishing without open access choice in hybrid journals. So how to find...

18 September 2020 5,861 3 View

How it is possible that DNA primers previously working suddenly stop to worked?

I have used the same exact sequences in primers while ordering the new primers. The old primers are that I used previously which was worked successfully. Similarly, the sequences in tubes are also...

20 August 2020 3,132 12 View

How to perform Reciprocal Space Mapping (Symmetric and Asymmetric) XRD for oriented thin films?

Let's suppose I have an STO substrate and I have deposited a thin film of another material and it is highly oriented and STO as well as my material both form are cubic. To better understand the...

14 May 2020 6,359 3 View

Can we calculate the average value of the particular sub-region of Raster TIFF image?

1) I have calculated various Drought Indices for all the 26 Mandals of the Warangal Region India. Can I calculate the average value of a particular drought index in any sub-region directly by...

19 April 2020 1,127 7 View

Is it possible to establish the relation between the Remote sensing based Vegetation Index and on field Crop area sown Data?

I calculated vegetation indices (MSI, NDVI, NDWI, NMDI, SWCI) for the Warangal region of India from 2014 to 2019 (May month) by using Landsat8 data. I got the on-field data of crop area sown from...

17 April 2020 1,943 2 View

How to apply deep learning for estimation of various parameters in single carrier system?

Parameters like carrier frequency, symbol timing offset and symbol rate estimation in a single carrier system.

23 February 2020 2,980 4 View

Cosine Similarity between columns of two dataframes of differing lengths ?

Hi All I have text column in df1 and text column in df2. The length of df2 will be always > length of df1. I want to calculare cosine similarity for every entry in df1[text] against every entry...

30 December 2019 7,453 1 View

How to perform antiferromagnetic DFT calculations?

There are three types of antiferromagnetism, namely A , C and G type. I want to perform DFT calculations with these types of antiferromagnetism using either Quantum Espresso or Wien2K codes in...

24 October 2019 7,175 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

Is it possible to do optimization for a submodel in Abaqus?

I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...

24 February 2021 4,908 5 View