How to get bibtex format for latex from nature articles?

I want to add reference article in to my thesis.bib file. Does anyone know how to export from nature articles?

06 July 2015 428 4 View

What is hopping length? Does it have a colleration with site preferencies of a atom in a lattice?

01 February 2015 7,159 5 View

What is the space group of Graphite Oxide?

The article is attached. How can they decide peaks, and write indices? According to which space group?

11 December 2014 5,847 0 View

What is the main idea behind thin film superconductivity?

If there are no long range order in thin films, how one can claim the Cooper pair mechanism exists in amorphous materials?

11 December 2014 6,517 8 View

Is it true that when your multimeter does not beep in continuity check mode, then your material is an insulator?

When checking electrical conductivity in a bulk material, we test it by a continuity check mode in a multimeter. How much current does the multimeter drives to your bulk sample? Can you say that...

10 November 2014 2,100 7 View

Is it possible to use emu/g unit for magnetization of a thin film?

10 November 2014 8,522 5 View

Is there a specific setting for XRD measurement on thin film?

I wonder if output power of an X-Ray diffractometer can be adjusted. For Raman measurement it is possible. What about XRD? Does it change the penetration dept (if any) in a thin film?

10 November 2014 4,408 11 View

How can I calculate total time for an XRD measurement?

09 October 2014 9,116 17 View

How can I cut glass substrates for coating?

I make thin films and I use glasses as substrate. A single grid's dimension in my evaporation system is 16mm x 6mm. I work in 10-6 Torr vacuum. How can I cut my glasses with rectangular geometry?

09 October 2014 3,205 15 View

Can Peierls distortion be a reason for superconductivity?

According to my knowledge, Peierls distortion is due to symmetry breaking in some crystals. Lets consider iron pnictide systems. It is known that BCS Theory for superconductivity is based on...

08 September 2014 1,439 20 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View