Is there a possibility in the Revit to suggest a suitable structure for the general form of the building?

27 August 2021 1 7K Report

Is there a possibility in the Revit to suggest a suitable structure for the general form of the building? Such as the interior architecture field, which suggests how the devices are arranged in space.

Usama Badawy

Please follow the under mention link this regards :

https://www.youtube.com/watch?v=nGf8a5qUy-Q

Badges
Science topic

Similar topics
Solid State Physics
Devices

More Maede Jabbari's questions See All

How can I model a rotor with bearing boundary condition in abaqus?

I want to model a rotor. it has 2 bearing to connect to the earth. in the intraction module I set bushes. but i dont khow whats its boundary condition.

13 April 2020 5,758 1 View

Which face of cellulose acetate membrane should be used?

The cellulose acetate membrane which I have, have different faces apparently. One side of this membrane is glossy while the other side of it is matt. I want to use this membrane for vacuum...

26 August 2019 3,492 3 View

How to build a reverse osmosis water purification setup?

I want to know exactly that how can I build a reverse osmosis setup with a circular layer of membrane which should be between the feed and the permeate part? What kind of apparatus should I use...

09 March 2019 5,836 4 View

How do I calculate residue residue distance between two series of aminoacid?

Hello, all. I want to calculate distances between two groups of aminoacids in gromacs (residue residue distance ). I can't use g_dist or gmx distance, because I don't want calculate the distances...

15 November 2015 1,561 6 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Is stone a sustainable material? Is it a sustainable approach to use natural stone waste in architecture?

I'm designing a zero-waste restaurant and considering using marble waste to make some tables and a bar countertop. My clients think it's not "sustainable enough" and I would like to have more...

01 March 2021 4,326 7 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View

How to get better phase shift in C-V curves for ferroelectric devices?

I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...

16 February 2021 8,514 2 View

Which DL architecture is better to work on handwritten data?

I am working in the area of Handwriting recognition for Bangla. As there are many DL architecture, I am confused which one to select.

15 February 2021 4,996 1 View