Is the use of a grinding aid in cement grinding mill beneficial? Does it really help in reducing specific power consumption?

09 October 2014 0 10K Report

Different types of grinding aids are available in market. My personal experience suggests that chance of reducing specific power consumption in cement grinding is 50-50.

Badges
Science topic

More Bhautesh Mistry's questions See All

Is there any model/equation to predict the erosion of SS pipes due to flowing water?

I am trying to design a heat removal system for a specific application. As the heat flux is very high, the only way to reduce the temperature is by increasing fluid(water) velocity. I am worried...

27 May 2024 3,804 4 View

Can any one tell me the indirect method to calculate SOD based on Quercetin?

Full method and formula to calculate SOD based on Quercetin in animal tissue

08 March 2024 6,303 0 View

What is the purpose of using stain and destain in SDS-PAGE gel?

Purpose of using stain and de-stain in SDS-PAGE gel

21 December 2023 9,902 4 View

Is anyone has access to SciFinder?

if yes then please help me. I want to search some patents. Thank you in advance.

19 March 2023 1,984 0 View

What sequence will we send to Eval-AD5754R to get a output voltage of 4 channels DACA,DACB,DACC,DACD?

As per the Ckt diagram and pin config we had connected the Eval with logic analyzer but the analyzer cannot provide any bits generating from the DAC. Thanx in Advance. #embedded_systems #VHDL...

20 April 2022 476 0 View

Patterning of PEDOT:PSS utilizing orthogonal resist?

I am trying to pattern a spin coated PEDOT:PSS layer (CLEVIOS PH 1000 + ethylene glycol + dodecylbenzenesulfonic acid + 3-glycidyloxypropyl trimethoxysilane) by utilizing Orthogonal OSCoR 4020...

15 September 2021 3,949 2 View

How should i fit my ITC data showing multi site binding?

I am titrating an iron-porphyrin catalyst into a solution of carbon nitride quantum dots (g-C3N4). Analysis of the binding was done using ITC, where i found an unusual isotherm. I recognise a...

20 April 2021 758 6 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 2,213 3 View

What are the limitations of ESP32 as a GateWay?

Limitations in terms of how many device connected, battery and power consumptions.

23 December 2020 8,270 1 View

MQTT Publish ans Subscribe with Node-Red?

I designed MQTT PubSub architecture in Node-Red. After that I did deploy the single MQTT communication and connections is successfully. But after that I clicked the message for sending sensor data...

14 December 2020 1,937 0 View

How to solve the problem of unconscious teeth grinding during sleep at night?

One of my friends, every night after falling asleep, his mouth would make a creaking sound after chewing something. This teeth grinding condition would continue until he woke up, and he didn't...

08 August 2024 1,366 5 View

Please, what is the memory consumption of the Matlab function quad tree decomposition procedure [S = qtdecomp(I)] with respect to the input set I?

27 July 2024 5,455 2 View

What is the average energy consumption per gate operation with superconducting qubit?

Could you provide information on the average energy consumption per gate operation when using superconducting qubits, specifically focusing on the microwave power required to implement gates? I...

15 July 2024 954 0 View

How to convince decision makers to adjust the legislation to allow opening of drug consumption rooms?

In my country, there is a lot of public outcry in relation to the presence of drug injection and related behaviors in public. Hence at least the bigger cities would probably benefit from the...

08 July 2024 8,903 1 View

Issue with micrometer beam size while simulating moving heat source problem?

I am trying to replicate results published in the journal paper published recently (Modeling of Laser-assisted micro-milling Inconel718 ). In that paper, they used vdflux subroutine to obtain...

05 July 2024 3,701 0 View

Can advanced wastewater treatment processes be integrated with real-time monitoring and adaptive control systems?

How can advanced wastewater treatment processes be integrated with real-time monitoring and adaptive control systems to enhance the removal efficiency of micropollutants and pathogens, while also...

28 June 2024 4,859 3 View

Initial and final setting times of a calcium phosphate cement?

I'm measuring the setting time of a calcium phosphate cement using an apparatus that records how much resistance a needle (connected to a load cell) encounters over time. This process provides...

24 June 2024 7,534 5 View

What is the most effective and best way to produce and purify water without using energy or with low energy consumption?

Greetings and Regards Water is the most precious gift that God gave to living beings and is the main element of the universe. Water is the origin of life and the beginning of the life of all...

23 June 2024 2,057 4 View

How do I control powder volume in a mechanochemical reaction?

Here is one case: I want to perform X + Y in the presence of Z catalyst in a 50 mL milling jar with 8 12 mm milling balls and investigate whether the the amount of catalyst affect the yield of the...

18 June 2024 2,706 1 View

Why does the color of silica gel changes significantly when milled in stainless steel jar?

Whenever I mill silica gel with other materials in stainless steel milling jar, the color of the powder goes from white (initial) to dark and darker color like yellow, dark yellow, brown, dark...

16 June 2024 3,984 3 View