Is the static pressure at the locations around the pump impeller represent the forces act on it?

More Ahmed S. Mansour's questions See All

How do we correctly setup the solar ray tracing for a Photo Voltaic PV panel simulation in ANSYS FLUENT?

Hello, I have a simple model (PV cell+ air channel) and I do not know how to let the sun rays hit the PV surface and then transfer the heat to the air..What I see is the sun rays hit the air...

08 September 2019 475 2 View

What are the equations of the boundary layer of a flat plate that TDMA method is based on?

Hello, I need the equations that show the coefficient of the matrix that solves the velocity contours of the boundary layer over a flat plate. I have the explicit discretization equations but I...

05 June 2019 7,941 4 View

How to define a heat flux and convection coefficient at the same time on a wall using user defined function in FLUENT?

Hell, how can we write a UDF to include a heat flux value + convection coefficient for a wall in Fluent because we cannot define two named selections for 1 wall ? Danke!

05 June 2019 7,041 12 View

How can we define a symmetry wall boundary condition in Fluent?

Hello, I want to simulate the half of the domain and define a symmetry wall because I do not want to consider it as the edge wall, I want to consider it the wall at the half of the domain..How ca...

04 May 2019 5,819 3 View

How to use Chemkin to model the model studied in the attached paper?

Hello, I want to know how to use ANSYS Chemkin to model the attached model in the attached paper. the videos on internet are so simple. Thanks

04 May 2019 3,934 2 View

Can we cople between ANSYS FLUENT and Simplorer ASAP?

Hello, we have done a simulation using ANSYS FLUENT, can we couple it with ANSYS simplorer? And if yes, how and what are the documents I can study? Danke!

03 April 2019 2,674 6 View

How can we define a heat flux boundary condition + convection for one wall in ANSYS FLUENT?

Hello, I have a wall which is affected by a heat flux and it is cooled by convection..How can we do this in FLUENT? Thanks

02 March 2019 5,946 4 View

What are the equations used to simulate a steady state thermal analysis using FEA ANSYS thermal?

Hello, we wanna write a thesis and we need the equations used for simulating the temperature distribution over a PV panel.. Where can we get these equations that ANSYS uses ? Thanks

31 December 2018 5,790 5 View

How can we save calculations to a text file from a Matlab CFD code during running the code like ANSYS FLUENT?

Hello, we have a CFD code written in MATLAB and we wanna save the calculations at a specific node to a text file like ANSYS FLUENT..Any suggestions please? We will be extremely grateful! Thank you!

31 December 2018 816 3 View

How to save data in a file from MATLAB GUI?

Hello, we have a MATLAB GUI code and it produces a graph, we need to save the data of the graph in a txt file, how can we do it? Thanks

09 October 2018 6,552 4 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can I represent SDS-PAGE results for machine learning analysis?

I am trying to classify and analyze the results of an SDS-PAGE based array for bacterial detection using machine learning, but I have trouble finding the best way to represent the results with...

27 February 2021 9,176 3 View

Hıdır Yankı Kılıçgedik

Yes.

Take note of X, Y and Z values of mass-weighted average of static pressure from surface integrals. From there you can also find the direction of force vector. Also, I strongly recommend you to compare your results with the theoretical calculations. You can find informations about force calculations in following books:

Gulich - Centrifugal Pumps (Calculations are unnecessarily complicated but very accurate)

Hydraulic Institute - Centrifugal Pumps

Lobanoff - Centrifugal Pumps: Design and Applications (Very rough estimation but still useful)

Ahmed S. Mansour

Thank you sir !