MY BOD incubator could not adjusted less than 25. Is it correct to use it in BOD test?
What is the difference between broad and sharp cyclic volatmmetric curves? and what are the reasons for broad curve? especially when analyzing carbon material?
01 February 2019 9,802 1 View
Can I use distilled water as catholyte in MFC? or if I use Potassium ferrocyanide, can I dissolve it in distilled water instead of buffer solution?
11 December 2018 1,374 0 View
Light produced by bioluminescent microorganisms is composed of photons, are they able to stimulate photosynthesis in other marine organisms? Thsnk you.
03 April 2018 3,318 0 View
I am preparing to study the effect of pH on bacterial activities, what is the perfect way for that: 1. Using different buffers and adding the medium components? or 2. Adjusting the medium pH by...
02 March 2018 3,995 2 View
Is it enough and acceptable to mention that the observation of fluorescent color is a clue that my strain is pyocyanin producer? Thanks
11 December 2017 8,941 0 View
In the Energy efficiency equation, how can I get the heat of combustion? Thanks.
10 November 2017 5,310 1 View
When I run the polynomial fitting on my data, a curve named "Residual curve"b appear after calculation, what is the meaning of that curve? and is it acceptable to use it instead of the fitting...
10 November 2017 1,342 0 View
I am working in Microbial fuel Cell (MFC) and want to calculate number of electrons involved in reduction of oxygen. Thanks
10 November 2017 8,456 0 View
Can you help me getting method (s) for rapid extraction and identification of these three Pseudomonas products? Thank you.
10 November 2017 2,134 0 View
How can I use origin in getting the slope of any curve? Thanks.
10 November 2017 5,738 0 View
03 March 2021 8,272 1 View
Hi, I am planning to apply for the PhD degree in the Supply Chain Mgt. with specific area of "Cold Storage warehouses" during Pandemics and wars. Where lock downs and shut downs are frequent....
02 March 2021 285 2 View
Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...
01 March 2021 2,327 1 View
I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...
25 February 2021 2,615 3 View
Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...
25 February 2021 9,602 4 View
What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?
24 February 2021 8,219 2 View
I'm running an EMSA to show the DNA binding activity of recombinant proteins versus the Wild type. Previous assays run by my research group using a different test system show the protein-DNA...
24 February 2021 8,325 1 View
I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...
24 February 2021 3,476 4 View
Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...
23 February 2021 9,159 3 View
I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...
22 February 2021 5,254 1 View