How can I get the heat of combustion in Energy Efficiency equation for MFC?

Fatemah Allam @Fatemah_Allam

11 November 2017 1 5K Report

In the Energy efficiency equation, how can I get the heat of combustion?

Thanks.

Deepak Jadhav

You have to use bomb calorimeter method for the same.

Badges
Science topic

Similar topics
Heat

More Fatemah Allam's questions See All

What is the explanation of broad peak in cyclic voltammetric curve?

What is the difference between broad and sharp cyclic volatmmetric curves? and what are the reasons for broad curve? especially when analyzing carbon material?

01 February 2019 9,931 1 View

Is it important to add buffer in the cathode chamber of MFC?

Can I use distilled water as catholyte in MFC? or if I use Potassium ferrocyanide, can I dissolve it in distilled water instead of buffer solution?

11 December 2018 1,554 0 View

The llight produced from bioluminescent bacteria, is it able to stimulate photosynthesis in other nearby bacteria and other photosynthetic organisms?

Light produced by bioluminescent microorganisms is composed of photons, are they able to stimulate photosynthesis in other marine organisms? Thsnk you.

03 April 2018 3,443 0 View

What is more accurate to study the effect of pH on bacterial activities, preparing different buffers at different pHs, or adjusting the medium pH?

I am preparing to study the effect of pH on bacterial activities, what is the perfect way for that: 1. Using different buffers and adding the medium components? or 2. Adjusting the medium pH by...

02 March 2018 4,134 2 View

How can I write in my thesis that a Pseudomonas isolate is pyocyanin producer?

Is it enough and acceptable to mention that the observation of fluorescent color is a clue that my strain is pyocyanin producer? Thanks

11 December 2017 9,069 0 View

What is the "Residual curve" regarding the polynomial fitting?

When I run the polynomial fitting on my data, a curve named "Residual curve"b appear after calculation, what is the meaning of that curve? and is it acceptable to use it instead of the fitting...

10 November 2017 1,464 0 View

How can I calculate number of electrons involved in electrochemical reduction of oxygen?

I am working in Microbial fuel Cell (MFC) and want to calculate number of electrons involved in reduction of oxygen. Thanks

10 November 2017 8,602 0 View

How can I obtain slope of any curve from Origin 6.0 or 8.0 software?

How can I use origin in getting the slope of any curve? Thanks.

10 November 2017 5,906 0 View

What is the fastest and accurate method for extraction and identification of polysaccharide, pyocyanin, and rhamnolipid from culture of Pseudomonas?

Can you help me getting method (s) for rapid extraction and identification of these three Pseudomonas products? Thank you.

10 November 2017 2,250 0 View

About polarization and power curves, is there a method to use potentiostat, without the need for changing different external resistances?

The common method of determination of polarization and power curves of Fuel cell is to change different external resistance and read the corresponding voltage and current. I would like to ask is...

10 November 2017 6,417 2 View

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

Could it be a cell culture contamination?

Hello everyone! I observed in my culture (htert-RPE1 cells) an orange- red particle at the bottom of the dish. It is visible to the naked eye as a very very small red dot. Could it be a...

09 August 2024 2,824 3 View

Is there any way to quantify bacterial and fungal cells in their mixed culture?

I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...

07 August 2024 7,535 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Why activated CAR-Jurkat cell could not kill targets?

Previously when I co-coluture anti-CD19(FMC63) CAR-Jurkat with Raji with E:T=5:1, Jurkat can eliminate Raji in 24h. However, when I test another CAR construct, although I can dectect totally CD69...

06 August 2024 641 2 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

How to isolate lymphocytes from mouse spleen?

I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...

04 August 2024 9,913 7 View

How to Add Missing Water Molecules in Protein-Membrane Simulations?

I have protein-membrane simulations (PDB, PSF, DCD) and have noticed that water molecules near the protein are not visible in the simulations. How can I fix this issue? Is there a way to place the...

04 August 2024 1,200 2 View