I little bit confuse with the term and wish someone can tell me more about the higher order factor and lower order factor. Is it the same as first order and second order? Thank you in advance.
what is the proper solution to increase AVE level to ensure all the AVE and CR are meet the requirement in SEM?
31 December 2017 1,468 0 View
I got confuse when happiness and subjective well being has been discussed in the same paper to see the outcomes.sometimes measure happiness but report subjective well being as an outcome.how...
01 February 2016 7,911 2 View
instead of Oxford happiness questionnaire, is there any instrument that can measure happiness in accurate way?
31 December 2015 1,864 7 View
As far as i review on happiness. i do see the pattern that most of the paper discussion on hedonistic and eudoimonic perspectives. but, my research concern is on self and social strength and...
31 December 2015 4,107 0 View
Is that about the scale or contradiction of idea?
31 December 2015 9,829 3 View
i would like to see the pattern of common factors contributing to the adolescence happiness especially in coping the problematic and conflict during the developmental stages
09 October 2015 9,128 2 View
focusing on adolescence happiness which talking more about psychology perspectives rather than other disciplines.
07 August 2015 5,762 0 View
07 August 2015 5,013 0 View
Does anyone know about the model of functioning happiness. I do have the model but the history of the model itself is not clear. Can anyone help me?
04 May 2015 1,891 5 View
approximately to know the milestone of development to handle the storm and stress stages in adolescent's life
02 March 2015 8,606 1 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...
31 July 2024 9,733 3 View