In real structures, can we use such strengthening technique?
A bunch of flower for everybody. I would like to ask about the list of journals which we can publish our paper for free. Thanks in advance. Sincerely Walid
25 February 2021 9,790 3 View
Hi there! My lab has been brought an array of C-4 I cell line. The cells did not succeed in attaching to the bottom of the flask and remained floating in the media. Although we followed the...
04 February 2021 10,018 5 View
ochratoxine A ; HPLC ; green coffee
29 December 2020 4,028 3 View
hi everyone, I have developed a simulation of a roundabout with a fixed time regulation, the lines of traffic lights in the roundabout are for vehicle storage. my question is: when we regulate by...
16 December 2020 1,923 3 View
Hello everyone, hope you are doing well. I made a simple traffic actuated control logic using VisVAP Stage 1 is for Vehicle Stage 2 is for Ped the compilation in VisVap run with success, but...
07 December 2020 553 3 View
Hi there, I am looking to purchase an UAV with an attached multi-spectral camera to use its images in delineate the shoreline. I need to take a vertical geo-referenced image (if possible) and...
21 November 2020 1,283 3 View
How can i delaying a signal in Matlab script file without using simulink block? (i want the instruction of delaying a signal in script file )
27 October 2020 4,299 2 View
24 October 2020 9,262 7 View
There are many universities that have excellent scholarship opportunities for international students.
21 September 2020 3,391 4 View
Hi everyone, I used MgSO4 as a drying agent to suck all water droplets from my organic extract. However, even after adding MgSO4 three times and leaving it overnight, I still see some water...
14 September 2020 9,203 3 View
Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...
22 February 2021 7,528 3 View
Some advice are about FRP (Fiber Reinforced Polymer)
07 July 2020 1,931 2 View
Dear researcher, Is there a chance that experimentally obtained ultimate tensile strength (UTS) of fiber reinforced polymer (FRP) reinforced with nanofiller can become higher than the value of...
05 January 2020 1,596 1 View
I am calculating for interfacial slip and bond shear stress to to draw load-slip and bond shear stress graphs of FRP and concrete interface from experimental test values. The problem is I put for...
09 October 2019 8,345 2 View
In the experiment, I used FRP laminate inside the concrete as shear reinforcement. The laminate was anchored from the top on the concrete surface. In Diana, the FRP can be modelled as...
07 August 2019 2,268 4 View
I am modeling a prestressed concrete slab strengthened with NSM FRP strips using ABAQUS I'm experiencing early debonding at a lower load than the experimental results I'm modelling the contact...
06 July 2019 3,788 2 View
Does any one know how can model FRP reinforcements inside the concrete using Diana software? Also, does Diana consider the reinforcement bar as a truss element or as a beam element? Regards
06 July 2019 7,397 3 View
03 July 2019 1,046 2 View
I am trying to model diffusion in fiber and matrix in a FRP bar, and the diffusion coefficient of the two domains are different. Similarly, my initial condition is zero concentration within the...
04 May 2019 9,226 5 View
In the first figure you can see how this model is loaded in the second figure the deformation is shown.The loading is just a boundary condition of 10mm and connection between FRP and concrete is...
21 March 2019 8,581 3 View
