FBG simulation in comsol
At first please see the attachment. This experiment was performed for a period of 7 days (n=100). After 7 days, we found different level of survival rate (%) for each treatment. Now, I want to...
15 February 2021 9,145 2 View
The organo montmorillonite nanoclays modified with octadecylamine were used for the experiment. After acid treatment, the surface area will be increase. However, in my experiment, the surface area...
10 February 2021 1,581 3 View
Dear all, I am trying to optimize a bimetallic complex using # opt=tight b3lyp/lanl2dz scf=qc geom=connectivity. The program is running for around 5 days but the size of the .chk remains same...
05 February 2021 8,721 3 View
The recommended amount of DNA for restriction digestion is 1ug in a 50ul rx I've got around 500-600ng of DNA in a total volume of 35ul. Would I get satisfactory results with this amount of DNA for...
31 January 2021 729 6 View
Please share your experience on the effectiveness or challenges on online teaching during Covid-19 lock down. Share your experience about challenges, technology, online learning platform,...
26 January 2021 4,532 37 View
Recently I have generated LC-MS metabolomics data. After annotation, some have their compound name but either no KEGG id or KEGG id but no pathway. How to interpret those compounds? Additionally,...
18 January 2021 1,938 3 View
The current global pandemic, the climate crisis, the destruction of the oceans (with plastics, etc), and massive numbers of refugees are part of a set of serious global problems. It is clear...
13 January 2021 2,022 3 View
I want to remove a duplicate citation
01 January 2021 3,983 3 View
Hello, I am a newbie in geant4. I'm learning it playing with example. Sometimes, when I go to simulate an example code, it doesn't create an executable file (the green one in my ubuntu terminal)....
26 December 2020 9,482 3 View
Hello all, I want to do glycosaminoglycan (GAG) simulation in Gromacs. Initial structure and CHARMM topology for short chains can be obtained from Charmm GUI glycan modeler. But I have to take...
23 December 2020 6,092 2 View
Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...
02 March 2021 4,624 4 View
How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...
02 March 2021 9,833 3 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !
01 March 2021 2,501 3 View
I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...
28 February 2021 8,626 3 View
Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...
28 February 2021 400 1 View
I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...
26 February 2021 1,511 3 View
I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...
26 February 2021 8,567 3 View
We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...
25 February 2021 568 1 View
Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...
24 February 2021 249 3 View