Is it possible to model Two phase flow boiling in COMSOL , by using the multiphase flow module?

More Ajith Krishnan's questions See All

How the critical heat flux vary with channel size for the same mass flux? Is there a general definition such that CHF increases with channel size?

If we take same square channel of different sizes, and allowing same mass fluxes through both, the small one or the bigger one can withstand the early dry out. I conclude the bigger one since...

08 September 2018 7,557 1 View

Does two phase frictional pressure drop has any dependency with gravitational orientation.? Does change in flow ( up flow or down flow) matters?

01 January 1970 4,753 0 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What analysis to choose with a large neste dataset and clearly skewed or kurtotic distributions?

Hello! I have a dataset of n=3000 nested within 8 countries with approximately 200 or 400 responses in each country. I originally planned to perform multilevel modelling with 4 dependent variables...

02 March 2021 6,865 1 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

How to plot the probability paper of Gumbel distribution using R programing?

In R-studio, there are many commands of Gumbel package. Arguments are also different. I`m asking about the alpha parameter of the Copula which must be greater than 1. If this is the one used to...

25 February 2021 5,229 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Unknown debris sheets observed in cell culture flasks?

Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...

25 February 2021 3,443 4 View

Can I use TCA instead of TFA for protein analyis in RP-HPLC?

I am trying to analyze lipase using the reverse phase-HPLC C18 column. In the literature, 0.1 % TFA was and 60% ACN was used. Can I use TCA in place of TFA? If any other methods are available to...

25 February 2021 2,388 3 View

Can we proceed to perform Two-way Mixed-ANOVA despite normality violations?

While testing assumptions, Shapiro-Wilk Test failed. However, I proceeded with the analysis and the interaction effect was significant. During our course- lectures, it was mentioned that Anova...

24 February 2021 228 3 View

Omar Rafae Alomar

Yes you can use COMSOL for modeling two-phase flow model

Ajith Krishnan

Thank you for your reply, Which module do we need to use?

Meng Wang

Depending on your need to track the interface or not, there are generally two groups of models. The following article gives a comparison in a nutshell:

https://www.comsol.com/blogs/which-multiphase-flow-interface-should-i-use/

Thank you for your answer.

Samra Harkat

interseting ,thanks

Leonidas Asimakoulas

Hi everyone,

I am wondering if someone doesn't have a specific module in COMSOL can they build the necessary equations from scratch. In my case, I only have a single phase flow but I need to model a two phase flow system. Is it possible to build it myself?

Thank you.