Specify the Burgers vectors for dislocations, which cannot be uniquely identified.?

1. A bcc metal single crystal was sliced along (1 -1 0) plane for TEM study. Assuming that the TEM available is equipped with a goniometer stage which tilts up to 45o. The Burgers vector of...

20 February 2021 2,370 1 View

Problem in energy minimization using Gromacs?

I have done energy minimization of DNA using Gromacs with tutorial lysozyme in water. The potential energy curve show a steep drop.

18 February 2021 4,822 2 View

How to improve dissolution of neosome?

I have made neosome from herbal drug. Neosomes are stable. But I face problems in dissolution. I used minimum ratio of 1:1:0.25 ( Drug:span 60: Cholesterol and GMs. Now how can I active better...

17 February 2021 3,584 1 View

What is the best method for preparation of Polymeric nanoparticles for co-delivery?

We are planning to make Polymeric nanoparticles for co-delivery of 2 flavanoides. Which is the best method, that one should follow.

09 February 2021 7,086 8 View

OmniScriptum Publishing Group?

Hello, Has anybody published with OmniScriptum Publishing Group. I got an email from them. The emails claims the editor is from the group but the email is signed out by lambert academic...

08 February 2021 5,611 3 View

Which one is better for storing energy: Fuels synthesized from CO2 or Hydrogen?

Based on educated guesses, which one of the following promises a better future for storing energy for grid scale, automobiles etc as opposed to batteries: 1) Fuels synthesized form CO2 2)...

02 February 2021 8,741 6 View

Is there any software to generate pdb of G quadruplex?

I have a DNA sequence which has predictability to form G quadruplex . I need a software to generate a pdb of it which will form G quadruplex. I am using open Babel but I am not able to set the...

29 January 2021 6,190 4 View

Following is XRD of iron oxide nano material synthesised using bipyridine derivatives. What are the reasons for Broad Humps?

Even after few repetitions..I am getting similar results. Is is due to organic components?

20 January 2021 9,279 6 View

How much Ti and B (in ppm) is required for effective grain refinement and why?

To have the desired grain size in 6061 and 6063 Al alloy, what should be the minimum % of Ti and B pick up and what is the chemistry/metallurgy behind that?

07 January 2021 9,305 2 View

How to make AlV50% alloy by thermit route?

Kindly provide the technical papers/patents on the production of AlV50% alloy by thermit route, by using V2O5

05 January 2021 2,471 3 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

What are damage parameters for SMA while modelling on ABAQUS 2020?

I have given Elastic and Superelastic material properties, but I think we need to provide the damage parameters also. Please help me here.

16 February 2021 8,694 1 View

Are there alternatives to the Devarda alloy when estimating nitrogen?

Are there alternatives to the Devarda alloy when estimating nitrogen? devarda alloy is reducing the nitrate to ammonium

15 February 2021 8,838 3 View

Passivation of chromium cast Iron in high temperature?

14 February 2021 2,157 3 View

How can we quantify martensite in Ferrous and Titanium alloys?

How can we quantify metastable phases like martensite in Ferrous and Titanium alloys, in relation to their stable counterpart For example in EBSD, XRD, Optical? Eg, Martensite and Ferrite maps.

09 February 2021 7,572 3 View