Is it possible to fabricate an FGM of cobalt-chrome-molybdenum and hydroxyapatite?

More Sara Kowsar's questions See All

Could someone please provide a list of journals that accept the application of methodologies in nature-based solutions?

I am looking for journals that admit the publication of results from applying the IUCN Standard for designing and monitoring Nature-based solutions. Many thanks for considering my request.

23 July 2024 6,444 2 View

Pink bacterial colonies?

I am cloning an overexpression plasmid with my protein of interest tagged with mScarlet. After transforming my ligated product into DH5α bacteria and plating on LB agar, I noticed colonies with a...

22 July 2024 5,953 6 View

Cell proliferation assays suggestions?

What cell proliferation assay do you suggest? cyQUANT from thermo Fischer has good reviews, a lot of good articles for the kit from Abcam. and Promega kits look easy and straight forward.

21 July 2024 1,554 2 View

How do you assign allele numbers and sequence type after amplifying housekeeping genes by PCR for MLST?

How to assign allele numbers and sequence type after amplifying housekeeping genes by PCR for genotyping of S. pneumoniae strains by MLST using bioedit ?

19 July 2024 5,239 2 View

How to make chocolate milk ?

we want to produce chocolate milk industrally .Dose anyone have a specific stabilizer formula for this pourpose?

10 July 2024 3,791 1 View

What is your understanding of Precision Medicine?

This forthcoming study aims to gauge public awareness of Precision Medicine and explore how AI and ML technologies can enhance healthcare outcomes. Please consider contributing to this research by...

12 May 2024 7,554 0 View

Efects from trauma in vitiligo?

is there anay resarch about how psychological trauma affects vitiligo?

10 May 2024 5,976 0 View

Matlab codes on the beamforming technique used in intellegant reflective surfaces technology?

I am looking for Matlab codes on the beamforming technique used in smart reflective surfaces technology. Can anyone help me? I would, of course, acknowledge your contribution and cite your work...

02 May 2024 3,957 1 View

Could you please anyone help me to rectify the following error in my gaussian input file?

When I specify the number of processors = 4, my calculation works fine. But when I want to specify the number of processors more than four, the program gives: "Will use up to 8 processors via...

30 April 2024 3,071 1 View

Sanger sequencing problems?

Hello, I have problems with PCR fragment sequencing (Sanger sequencing on SeqStudio). We perform sequencing reaction with BigDye™ Terminator v3.1 with subsequent purification with BigDye™...

29 April 2024 4,613 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

How do you decide an optimal AC amplitude for non-faradaic electrochemical impedance spectroscopy?

I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...

16 July 2024 5,031 1 View

How can we simulate(with FEM) the shape of Mobius strip using Abaqus Learning edition?

Aim is to simulate the shape of Mobius strip (an elastic ribbon) in simple way ( using Abaqus Learning edition). In literature, Mobius strip is modeled as Kirchhoff Rod / Cosserat plate. But, such...

15 July 2024 4,388 1 View

How closely does an elastic sheet conform to what's below it?

See the attached file for an illustration of this problem. Consider an elastic sheet S (orange) that’s laying atop a solid base B (blue). The sheet is under tension (arrows) and is held to the...

30 June 2024 747 4 View

Why is Ca/P is higher than 1,67 ?

I prepare Mg doped Hydroxyapatite by wet preipitation but (Ca + Mg)/P ratio is higher than 1,82. CaO peak cannot be detected in XRD spectrum

23 June 2024 8,970 19 View

What is the difference between creep deformation and stress relaxation ?

I understand the basic definition for both. I found a literature to describe both of them. In the paper, they states: If a stress is applied to a concrete body, the body experiences an elastic...

19 June 2024 525 3 View

Can cross-slip, twinning and fracture systems, under applied loadings, receive the same mathematical theory?

Cross-slip, twinning and fracture are major deformation modes adopted by loaded materials. It appears sound that these apparently different deformation mechanisms can be analysed on the equal manner!

15 June 2024 8,477 3 View

Why is stiffness of structure reduced in pushover after gravity case?

So I have a structure with a pile foundation and a gravity load acting on the structure. The demand curve is drawn by running an elastic analysis. Pile-Soil is modelled as p-y, t-z, and q-z...

14 June 2024 5,220 0 View

Which solvent and substrate is found to be best suited for deposition of electrodes with MXene ink?

Suppose we have dried MXene slurry (Ti3C2Tx), then the combination of which solvent (in which this dried MXene slurry powder will be mixed, subsequently forming the "ink") and corresponding...

13 June 2024 5,763 0 View

Mohammad Khodaei

Dear Sara

I think you will have some problems during sintering. Because, Co-Cr-Mo alloy have sintering temperature higher than 1100 C, while HA will decompose at higher temperatures.

Hassan Nosrati

https://daneshyari.com/article/preview/5811464.pdf

María Alexandra Fajardo Perdomo

Hi,

Maybe you should review studies that have worked the CCM coating with other biomaterials and review the results obtained for the elastic modulus.