Is it possible to connect Sim power systems and Simulink in MATLAB ?

Sharon Balasubramanian @Sharon_Balasubramanian

07 July 2015 0 8K Report

I need to connect a battery (electrical modelling) and a converter (transfer function modelling) in MATLAB.

Badges
Science topic

Similar topics
Engineering
Modeling

More Sharon Balasubramanian's questions See All

How to model a battery using transfer function method in MATLAB ?

Since i modelled converters using tranfer function method, I need to model a usual battery, zebra battery and supercapacitor battery using transfer function method in MATLAB. If there is any...

06 July 2015 5,737 0 View

Can I perform an analysis on sandwich layer consist of nonlinear and linear layer in ANSYS?

Sandwich structure consist of 3 layer with middle layer nonlinear. Can i perform the analysis on ansys? If possible can i get the result of middle layer data output separately Modeled the...

06 July 2015 3,217 0 View

Any suggestions on dynamic / static analysis in ANSYS WORKBENCH or ABAQUS?

I am doing a project which has an eccentric cam driving a cylindrical follower. The cam is made of gear pair and is driven by a 3 HP motor and I need to find out the reaction at the probe. I tried...

06 July 2015 7,773 3 View

Is there any Journal or site for getting the dimensions to model a train wagon ?

Modeling by composites. Software using- Catia, Abaqus, Feast If there is any other relevant data related to this work please include that too with reply as attachment.

09 October 2014 4,879 3 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View