is coating PLA sheets with PEDOT: PSS by usual immersion/dip-coating possible?
Currently, I want to investigate the structural, electronic, and other properties of a composite material, but have trouble in developing the necessary input file for Quantum ESPRESSO (QE). So...
21 May 2024 3,409 3 View
the image of an error is attached to this questions below.
11 March 2024 4,226 1 View
We did some experiments on GCD measurements using sodium sulfate electrolyte. The supercapacitor is based on PEDOT-PSS. The GCD was not possible. Does it need any electrolyte additive? if so what...
15 January 2024 8,732 1 View
please, can any one help me?
29 December 2023 7,721 1 View
I wrote a book and I have a conceptual approach. I have my own understanding, on this topic and also philosophically and spiritually contained. How may I publish as a research paper and post it on...
25 October 2023 7,665 2 View
I want to simulate charge-discharge, CV, and EIS for my flexible supercapacitor. Which software fits for this purpose? Comsol Multiphysics, Simulink, ANSYS, or any other?
10 October 2023 2,520 1 View
I want to learn data science using R, Python, machine learning etc. Anyone who can send me the links for these training courses (up to 6 months) that are legitimate and can be accepted in USA?
04 September 2023 7,515 3 View
In most cases, we may obtain odds ratios or relative risks from the given beta coefficients if the DV is categorical to estimate the pooled effect sizes. What if the DV is continuous and report...
14 July 2023 8,713 3 View
I have coated 50 µL of PEDOT: PSS on a 25 x 25 cm dimension PET (0.513 gm in weight). I want to measure the GCD of my supercapacitor. How can I find the active mass of the electrode to set the...
12 June 2023 5,903 1 View
I try to measure the GCD of my supercapacitor and the pop-up message "cutoff on WE(1). potential occurred" comes out. Any suggestions on how to solve such problems is appreciable.
06 June 2023 9,819 4 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,294 3 View
I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose
25 July 2024 438 3 View
I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...
23 July 2024 4,074 2 View
We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...
09 July 2024 5,123 4 View
I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...
08 July 2024 7,327 4 View
We have been experiencing repeated what looks very much like fungal contaminations in several incubators (in the same lab). We have tried the following repeated times and yet the coating on all...
02 July 2024 6,375 2 View
Hello, I want to load Remedesivir (RNA polymerase inhibitor) into mesoporous nanoparticles (MSNs). The issue is drug is temperature and pH sensitive and it degrades quickly. I need advice on its...
01 July 2024 889 3 View