Is it necessary to keep threshold temperature for melt/refreeze always lower than threshold temperature for snow/ice?

08 August 2016 0 9K Report

While doing snow-melt modelling, is it necessary to keep snow-melt temperature below threshold temperature for type of precipitation? Why? Why not? Explanation please.

Badges
Science topic

Similar topics
Engineering
Modeling

More Amrit Thapa's questions See All

What is the better way to handle zeros for bias correcting the satellite based precipitation?

I am using gamma distribution for correcting bias in satellite based precipitation. Can you suggest me to handle zero values ?

31 December 2017 4,723 1 View

Anyone working with APHRODITE data in R?

I was trying to read APHRODITE data in R software but could not. Any solution?

10 November 2017 7,641 3 View

How to select a row based on minimum value on two columns?

I have a matrix with x rows and 2 columns. I want to select the row which has minimum value in both columns. But the problem is minimum value does not occur at the same time in a row. Is there any...

09 October 2017 7,254 0 View

How to read MSWEP rainfall data from R?

I am planning to use MSWEP rainfall data for some hydrological application. I decide to use R as i am familiar with it. Can anyone know how to read MSWEP rainfall data from R? I already tried with...

09 October 2017 1,522 3 View

How to install MODISSnow library in R (window operating system)?

I was unable to install MODISSnow library in window platform. Can anyone help me?

05 June 2017 9,398 0 View

Any paper that considers snow interception by plant for Himalayan catchment?

how important is snow interception by plant for central Himalayas. Any reference articles.

05 June 2017 9,009 2 View

Any R package for Vulnerability mapping?

Have you come across any vulnerability mapping package in R?

05 June 2017 4,862 0 View

How to calculate mean snow cover days?

I have raster file of snow cover days. Now i want to calculate mean snow cover days for whole raster. How to do this. Should i add values of all pixel and divide by those pixels which have snow ?

04 May 2017 6,695 2 View

What are the suitable statistical index for evaluation of gridded satellite rainfall products?

Could you explain which statistical index is better for evaluation of satellite rainfall product for Himalayan catchment?

01 February 2017 6,780 4 View

What are existing spatial downscaling techniques for increasing spatial resolution of grided climate datasets like APHRODITE, TRMM, CHIRP, MERRA?

I need to improve/increase the spatial resolution of gridded climate datasets from low to high (eg., 5 km to 90 m) for Himalayan Catchment. Can you suggest some?

31 December 2016 4,371 6 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View