Is doctor blading means applying paste with hand gives uniformity?

Bulkesh Siwach @Bulkesh_Siwach

11 November 2014 1 8K Report

applying paste with hand does not have uniform pressure over the surface.

Chuanyu Jiang

I t can be, but it also depends on the properties of the paste

Badges
Science topic

Similar topics
Thermodynamics
Pressure

More Bulkesh Siwach's questions See All

How do we increase the resolution of an image?

I have an image having DPI value 100 but the publisher want it to be of atleast of 300 dpi...so what will be the solutions..please answer as soon as possible. Thanks

07 August 2018 5,925 5 View

What is the significance of cyclic voltammetry (CV) measurements in the field of counter electrodes for DSSCs?

I have prepared three carbon based electrodes like graphene, MWCNTs, GRAPHENE OXIDE etc. and need to note CV of these. Please tell is this measurement is necessary for these counter electrodes...

10 November 2017 6,851 4 View

Is it suitable to use drop casting method for depositing films of counter electrodes of DSSCs?

I am to deposite films of MWCNTs and graphene for counter electrode for DSSC. Actually I need some research papers that can explain this technique in a detailed way....thanks in advanced.

09 October 2017 3,170 3 View

Can cyclic voltammerty is possible for powdered samples without coating films?

If yes, please suggest me the way..for doing this. If NO then why?

06 July 2017 1,594 2 View

What is the basic theory behind Tauc's Law for optical band gap calculation?

Please answer with literature references. Thanks in advance.

01 February 2017 2,246 3 View

What is the theory on which Tauc plot is based upon for band gap measurements?

Please attach me some papers regarding this..

01 February 2017 3,476 5 View

Can we find porosity values of thin film using ImageJ software?

How we can find porosity values of thin films using this software? please write the steps if someone have used it.

01 February 2017 7,963 5 View

Where does the HUMO and LUMO levels locate in Black Dye?

i want to know the exact energy level values..please attach some papers regarding use of black dye in DSSC.

01 February 2017 7,795 0 View

What are the absorbance regions of black dye as i have used it in DSSC? can i get some papers?

I have used N749 black dye as sensitizer in DSSC.

09 October 2016 5,414 2 View

What is the maximum reported efficiency of DSSC device with carbon materials as counter electrodes?

So As to compare platinum CE device with the carbon materials CE like carbon nanotubes, graphene etc.

06 July 2016 4,665 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

The HCP removal rate is lower than usual in concentration step, why?

Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...

11 July 2024 5,380 0 View

Pressure in Iron Iron Carbide?

What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?

05 July 2024 1,891 0 View

How to Perform Randall-Selitto Test (Paw Pressure Test) In Mice?

Hi All, My name is Sumaiya, a PhD student at the University of Queensland. I am looking for some suggestions on how to hold mice and perform Randall-Selitto Test by using Paw Pressure Randall...

30 June 2024 6,004 0 View

How do I dedicate my entire life in doing only one thing?

I would like to dedicate my entire life in doing only one activity alone and nothing else. How do I achieve it in this world full of unavoidable distractions and societal pressures?

24 June 2024 298 1 View

If modulus of elasticity is divided by any inertial or dynamic pressure (1/2rhov^2), is there any dimensionless number present to represent it?

While deriving for a momentum equation with elastic stress effects, I am planning to put a ratio between elastic modulus (in Pa) and dynamic pressure (in Pa) in a simplified form. I am not...

23 June 2024 8,059 1 View

Trying to find a copy of an original paper?

Despite many attempts I am still unable to find the original version of this paper and would appreciate if anyone can locate it for us: Baker PG, Haig G (1981) Metronidazole in the treatment of...

20 June 2024 5,448 3 View