Is carboxy methyl cellulose better than other hydrocolloids?

11 November 2018 1 2K Report

Hi guys;

I used carboxymethyl cellulose as an edible coating compared to other hydrocolloids, I'm now looking for an article that highlights the benefits of easy and cheap carboxymethyl cellulose extraction compared to other hydrocolloids. If someone has another reason to excuse the use of carboxymethylcellulose as an edible coating, compare it with other hydrocolloids please send me article. With respect

Razie Razavi

Thank you for recommended articles.

Regards

Badges
Science topic

More Razie Razavi's questions See All

What is the effect of solvents on mechanical properties of film?

Does anyone know which of the compounds of water, ethanol, acetone, and isopropanol as solvents, provides a higher mechanical strength (higher tensile strength) in the edible film (hydrophilic and...

03 April 2018 4,763 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Is it possible to use a safer acid instead of monochloroacetic acid to convert bacterial cellulose to carboxymethyl cellulose?

Hi, researchers, Is it possible to use a safer acid instead of monochloroacetic acid to convert bacterial cellulose to carboxymethyl cellulose?

29 July 2024 4,570 0 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

Is the use of microcrystalline cellulose MCC 102 in direct compression technology justified, given the low flowability of this excipient?

Hello everyone reading this topic! It is well known that microcrystalline cellulose 102 is recommended for use in direct compression technology, however, like other grades, it has poor flowability...

08 July 2024 2,807 0 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View