What is the most reliable source to get Impact factor of journals?

Source to get Impact factor of journals

01 March 2021 6,654 2 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

Best FE Program for Concrete Strengthened with FRP Sheets?

Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...

22 February 2021 7,528 3 View

Any information about dinitrosalisylic acid reagent end point color stability ?

I work on estimation of alpha amylase activity using dinitrosalisylic acid reagent If i put the reagent to stope the enzymatic reaction and allow the reagent to react with the produced reducing...

17 February 2021 7,402 4 View

Using liquids as superstrate in Fabry-Perot Cavity Antenna?

Hi, A Fabry Perot Cavity allows to increase the directivity of a low gain antenna by putting in the top of cavity a superstrate with high permittivity such as a ceramic (er=10.2). However,...

09 February 2021 6,799 8 View

Experiment statistical analysis?

07 February 2021 3,635 3 View

Distribution of modes fields ?

Hi, We find a specific distribution of electric fields in structure for different frequencies which can be seen using em solvers and known as modes. I would like to know how we can choose the...

04 February 2021 10,043 3 View

Greetings Doctors, If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers?

If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers can i use the same word in the writing of these 2 papers or this would considered as...

04 February 2021 4,648 4 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Does RNAiMAX transfection reagent work in serum free medium?

I diluted siRNA and RNAiMAX in opti-MEM and added to the cells which they were in the growth medium. Is it a right way? or should I culture cells in the opti-MEM medium for a while and not in...

26 February 2021 10,041 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View