How the adherence on glass substrate is ensured?

During the deposition of thin films glass substrates are used.

09 October 2019 3,291 3 View

What does average crystallite size mean in Scherrer method?

05 June 2019 2,195 3 View

Could anyone share the CIF file of hexagonal-MoO3?

Crystal Structure of MoO3 is hexagonal.

02 March 2019 3,742 3 View

What does the dislocation density signify for the prepared thin films?

The dislocation density is estimated from the following relation using the Williamson and Smallman formula.

11 December 2018 6,408 1 View

How many informations come from the FT-IR spectroscopy of thin films?

Characterizations of thin films are carried out by various techniques such as FESEM, EDX, XRD, FTIR, UV-visible spectroscopy and DC electrical measurements etc.

11 December 2018 5,389 0 View

Is the band gap related to the thickness of the thin films?

In our work pure TiO2 and Fe doped TiO2 thin films were deposited onto glass substrates by the spray pyrolysis technique with the substrate temperature 4500C. The structural, electrical, optical...

11 December 2018 3,833 3 View

What is the necessary band gap value of thin film for using in solar cells?

Oxide based transparent conducting materials such as TiO2, SnO2, ZnO, In2O3 etc. have been investigated over the decades for the solar cell application, architectural windows, heat reflectors,...

11 December 2018 4,304 0 View

What is the reason for shifting FTIR peak to lower wavenumbers?

I have characterized the sample by FTIR spectroscopy.

11 December 2018 3,132 2 View

What are the methods to calculate the crystallize size?

XRD pattern shows that the samples are crystalline in nature.

11 December 2018 3,336 4 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

How to size battery banks?

I am designing a small grid connected solar PV power-plant. As the battery's capacity is specified in Ah and demand in kWh. What is the best way to size the battery bank? I have battery price in...

28 February 2021 1,638 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Dapi fluorescence protocol for colon cell lines ?

28 February 2021 2,534 2 View

How to design a boost converter for a mppt controller?

I have a doubt on how to select the inductor and capacitor value when I want to implement MPPT controller. This is because we always take a maximum output voltage and current but in this case, we...

28 February 2021 3,637 2 View