In one of my study I used Serial Mediation, I used PROCESS_model given by hays and preacher model 6 for that, is it correct to use model 6 for serial?

30 May 2018 1 4K Report

Though I got same from other's work but still need confirmation to clear my doubt between Serial and Parallel mediation.

Matt Sykes

Yes that's correct. Parallel mediation is model 4.

Badges
Science topic

Similar topics
Correction

More Kamlesh Kumar Maurya's questions See All

How to do breeding in Fruits ?

kindly any give suggestion

10 June 2024 5,934 1 View

What is the significance level for fisher exact test if p value is 0?

in case of chi square testas well if p is 0.00 then how to interpret results and level of significance?

05 May 2024 7,662 3 View

Does any one know R package for least cost path and corridor analysis using genetic data?

Hi.. I want to do least cost path and corridor analysis from genetic data. I want to show possible dispersal corridor using hapotype (genetic data) for my target species. I know it can be done in...

12 March 2024 4,505 3 View

Why I am getting big difference in heat flow (mW) in slow heating and fast cooling cycle? Can I move my cooling cycle near to heating cycle?

Can I move cooling cycles of 20 and 30 oC/min close to 10 oC/min?

08 March 2024 947 0 View

During galvanostatic charge-discharge (GCD) measurements, why is the electrode not fully charged when lower currents are used ?

When applying currents ranging from 1 to 8 mA to charge my electrode, it fails to reach full charge, and instead, after some time during the charge cycle, it exhibits a straight line pattern on...

28 February 2024 1,535 3 View

How to decide sampling interval for seismic refraction project?

Hi All, We are working on a seismic refraction project where we are using 113 Geophones of 4.5 Hz. The geophone spacing is 2.5 m and the record length is kept 1 seconds. Aim is to record first...

28 December 2023 5,995 0 View

What are the basic processing steps in GPR processing for Geological layer picking?

I use REFLEXW software for GPR data processing. Task is to process and pick Geological layers and any anomalous area from MALA wide range GPR data. It provides two sets of data 1 for low frequency...

03 October 2023 208 4 View

What is Green House ?

A greenhouse, in the context of horticulture and agriculture, is a specially designed and constructed structure or building that allows for the controlled cultivation of plants. It's essentially a...

23 September 2023 4,779 2 View

Most Important Question of Entomology ?

What is the largest order of insects in terms of species diversity? Answer: b) Coleoptera In insects, what is the purpose of the tracheal system? Answer: a) Oxygen transport Which insect order...

23 September 2023 8,749 2 View

How to search research topic related to Agriculture ?

Help in Research title

23 September 2023 6,507 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How do you delete a duplicate pdf for the same paper on ResearchGate?

The first pdf file I uploaded had an error. So I uploaded an updated, corrected pdf of that paper with a different pdf name. I dpon't want the old copy to be download or read.

07 August 2024 9,508 1 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View