16 December 2021 4 535 Report

I have made ZnO pallet by adding KBr as binding agent. I want to do temperature dependent Raman Spectroscopy. Should I use KBr in general for this for making ZnO pellet? Or anything else binder should I use? All suggestions are appreciated.

More Arpan Ghosh's questions See All
How to find the mean, SD and CI in SPSS?

Hi, I hope that someone can help me with this task: I have 5 groups of participants which are numbered in SPSS from 1 to 5 (according to their group number) and are all under the variable group....

03 March 2021 506 3 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

What condition required for coating of Fe3O4@SiO2 by using APTES?

I tried coating Fe3O4@ SiO2 by using APTES in 5% water-ethanol but it is not coated. Kindly suggest a solution for it. Thanks

24 February 2021 5,992 4 View

What is the best way to calculate sample size for a multivariate regression model for adequate power?

GPower is only equipped to deal with calculations of bivariate regressions and needs SD s for both predictor samples. However, if one has a multiple regression with more than 2 outcome variables...

12 February 2021 6,911 3 View

How can I prevent bubbles from forming under a coverslip?

My colleague and I are having some trouble mounting 70 micrometer mouse brain slices. When we initially position the coverslip over the mounted slices, there are no bubbles but when we come back...

10 February 2021 3,580 1 View

What recipe of homemade lenti-virus concentrator do you use?

My lab is using a lenti-X concentrator. And we are looking for a homemade recipe. I have tried this recipe....

08 February 2021 5,965 1 View

What is the best visualisation solvent for xylooligosaccharides using TLC?

I am interested in using TLC to detect non-linear xylooligosaccharides. What would be the best visualisation solvent? Would aniline phthalate solution be suitable? I have also seen people...

02 February 2021 7,748 3 View

Similar questions and discussions
ZnS oxidizes to ZnO!!why??

when I put my ZnS solution in the chemical bath, the ZnS oxidizes so there are ZnO peaks appearing because of the reaction with the oxygen in the air, despite the fact that I close the beaker...

14 February 2021 5,778 9 View

Xrd result of ZnO thin film shown better crystallinity at low temperature and the crystallinity decreases as the temperature increased. why?

I have synthesized ZnO thin films at four different substrate temperature say, 300, 350, 400 and 450C. and the samples were annealed at 450C for half an hour. the xrd result shown better...

04 February 2021 7,641 4 View

What is the basis set to optimize ZnO using GaussView for DFT calculation study?

Greetings, I have a bit of problem in setup the basis set of my DFT study for ZnO.. As you can see in the image attached below, I use B3LYP 6-31G (d,p) for geometrical opt. of ZnO.. But sadly, I...

13 January 2021 7,508 4 View

What is the advantage of nanostructured ZnO thin film over continuous ZnO thin film for optoelectronic application?

What is the advantage of nanostructured ZnO thin film over continuous ZnO thin film for optoelectronic application?

30 December 2020 9,422 2 View

What is the best lubricant and dispersant for SiC abrasive particles ?

I am examining laboratory cases about ZnO Based ceramic Lapping with SiC,Al2O3,CeO2 and SiO2 abrasive particles. but i have no experience about modifying SiC slurry lapping. Also,i use of double...

13 December 2020 4,327 4 View

How to know if Zinc Oxide is coated on the glass substrates?

Hello all I have prepared Zinc Oxide nanoparticles using sol gel synthesis. I tried to coat the ITO and glass substrates with the ZnO nanoparticles ( dispersed in ethanol). But I am not sure if...

08 December 2020 3,692 8 View

How to get ZnO material using ATLAS Silvaco?

Hi everyone, I am not familiar using ATLAS Silvaco, I would like to ask, steps to define material not in ATLAS like ZnO and there is any input file should I include?

30 October 2020 5,704 3 View

Zno NPs seperation?

Thanks a lot for your answers. I have one more question: after synthesizing ZnO nanoparticles , I am not able to separate from the original solution (dispersion actually). The recipe is as...

23 October 2020 9,857 8 View

ZnO and PBABr synthesis?

Hello all, I want to synthesize ZnO nanoparticles and PBABr in my lab for my LED project. I know the method, but I am not sure how can I check(even visually) that I have arrived at the correct...

27 September 2020 5,334 7 View

Synthesized ZnO quantum dots cannot be well dispersed in ethanol, how to solve this?

I synthesize ZnO quantum dots (QDs) as an electron transport layer in this method: 10 mL ethanol containing 5.5 mmol TMAH was dropped into 30 mL DMSO containing 3 mmol zinc acetate hydrate within...

15 September 2020 6,470 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close