Could someone please guide me on how to set up boundary conditions to enable the recirculation of fluid from the outlet to the inlet with a specific recycle ratio in Ansys Fluent?
In CFD simulations, determining the appropriate inlet and outlet boundary conditions is crucial for accurately modeling recirculation phenomena in both two-dimensional (2D) and three-dimensional...
15 March 2024 3,203 1 View
Anyone who could help me by providing a method or software for analyzing the correlation between temporal rainfall attributes and crop production (Impact of rainfall seasonality on crop...
10 March 2024 9,752 3 View
I am working on complex survey data analysis. I have two or more primary sampling units per stratum. but my stata says that" it can not compute standard error due to only one primary sampling unit...
29 December 2023 7,470 0 View
In engineering applications, understanding the Reynolds number is crucial for predicting the behavior of fluid flow. For low Reynolds numbers, laminar flow is desirable in scenarios such as...
09 December 2023 4,608 10 View
Generally, choosing a turbulence model is a critical decision in CFD simulations for predicting laminar-turbulent transition, especially in complex flow scenarios. The model's ability to handle...
20 November 2023 5,218 1 View
In fluid mechanics and computational fluid dynamics (CFD), the fluctuating velocity components u' v' w'′ represent the turbulent fluctuations in the velocity field. These components are used to...
16 November 2023 8,105 6 View
Gerder studies are still important area of exploration for the transformation of any society in the globe.The aspect of power relation of gender is important exploration of anthroüpology.So is...
15 March 2023 5,467 0 View
Dears Tropical region is the hub of global biodiversity, however nations of this region remained poor.
14 August 2022 7,943 11 View
Dears How can we make the integral use of herbal or traditional medicines with conventional medicines to enhance the efficacy of the existing healthcare delivering systems?
20 July 2022 2,132 3 View
Some of the local landraces of cattle become competitive on the dairying system if husbadry practice is enhanced. Please share you thought and experiences.
10 July 2022 6,848 13 View
What should be the equation for halfway bounce back boundary condition for flow field with forcing term?
08 August 2024 7,938 1 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...
29 July 2024 1,092 2 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...
25 July 2024 9,058 4 View
I am an undergraduate mechanical engineering student seeking suggestions on topics related to either thermodynamics, fluid mechanics, heat transfer or renewable energy for my final year project....
24 July 2024 4,058 5 View
In terms of CFD, we often analyze the stability of the error using Von-Neumann analysis, especially for FDM based problems. Should we follow the same approach for a compressible fluid flow using FVM ?
13 July 2024 6,296 5 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View
hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.
03 July 2024 5,418 4 View